manualshive.com logo in svg

Lenovo ThinkCentre 0401, Hardware Maintenance Manual, Page: 130 / 170

Share
Download
Lenovo ThinkCentre 0401 Hardware Maintenance Manual Download Page 130

15.

Remove the four screws that secure the LCD panel to the main bracket.

Installing an LCD panel

To install an LCD panel, do the following:

1.

Place the main bracket over the LCD panel, make sure the four screw holes in
the main bracket align with those in the LCD panel.

2.

Reinstall the four screws that secure the LCD panel to the main bracket.

Note:

First partially tighten all four screws, and then fully tighten them. This
will allow the four screws to be installed correctly.

3.

Position the LCD panel and main bracket assembly over the front bezel,
making sure the screw holes in the main bracket align with the mounting
stands in the front bezel.

4.

Reinstall the 11 screws to secure the main bracket to the front bezel.

5.

Reinstall the system board. See “Installing a system board” on page 105.

6.

Reinstall the microprocessor and heat sink assembly. See “Installing the
microprocessor and heat sink assembly” on page 103.

7.

Reinstall the memory modules. See “Installing a memory module” on page 95.

124

Hardware Maintenance Manual

Summary of Contents for ThinkCentre 0401











































































































































































Reviews:

No comments