Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 151 | Manualshive

Page: 151 / 296

background image

Figure 76. Hard disk drive backplane (upper) removal

Grasp the backplane and pull it up and out of the upper tray.

If you are not installing another hard disk drive backplane after you remove the hard disk drive backplane:

• Install the fan cage. See “Install a fan cage (upper tray)” on page 125.
• Install the upper compute tray or storage tray. See “Install a compute tray” on page 117 or “Install the

storage tray (fully removed)” on page 234.

• Install the front cover. See “Install the front cover” on page 132.

If you are instructed to return the backplane, follow all packaging instructions and use any packaging
materials that are provided.

Remove a hard disk drive backplane (lower tray)

Hard disk drive backplanes in the lower compute tray are accessed from the front of the server. There are

several types of hard disk drive backplane. Steps that are backplane specific are noted in each procedure.

S002

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

.

Hardware replacement procedures

141

«
...
149
150
151
152
153
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Express 5800 Series

Brand: NEC Pages: 90

PDS-220F Series

Brand: ICP DAS USA Pages: 94

Brand: TANDBERG Pages: 127

Brand: Oki Pages: 4

Azure StorSimple 8100

Brand: Microsoft Pages: 12

88631SU - System x3850 - 8863

Brand: IBM Pages: 90

Brand: Gigabyte Pages: 115

Brand: Polycom Pages: 220

Brand: Ubiquiti Pages: 28

SUPERSERVER 5017C-MF

Brand: Supero Pages: 96

Brand: Olive Pages: 19

SUPERSERVER 5025M-UR

Brand: Supermicro Pages: 130

Brand: RIOT Pages: 18

Brand: Bodet Pages: 13

Brand: Dell Pages: 77

Brand: Dell Pages: 14

Brand: Dell Pages: 116

PowerEdge FC430

Brand: Dell Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands