Lenovo ThinkAgile CP 4000 Series Upgrade Manual Download Page 61

Page: 61 / 68

Step 7. Slowly lower the enclosure and ensure that the other three nailheads on each side slip into the

slots.

Figure 23. ThinkAgile CP compute enclosure installation

Step 8. To slide the ThinkAgile CP compute enclosure into the rack, first push up the rear latches on the

slide rails.

Step 9. Push the enclosure until the slide rails click into place.

Step 10. Push up the front latches on the slide rails.

Step 11. Push the enclosure all the way into the rack.

Figure 24. Enclosure installation into rack

Step 12. Fasten the two thumbscrews located on the front of the compute enclosure.

Chapter 4

Compute block capacity upgrade

Summary of Contents for ThinkAgile CP 4000 Series





































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Upgrade Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands