Lenovo ThinkAgile CP 4000 Series Upgrade Manual Download Page 13

Page: 13 / 68

Compute block

• 1 D2 enclosure, fully populated PSU, fan, 220V with 10Gb SFP+ network module

• Minimum 2 SD530 nodes, maximum 4 nodes

• 128 GB, 256 GB RAM per node

• 8+ cores per CPU, 1-2 sockets filled AXQT, and others

• 2x SFP+ DAC cables per node, 1.5m and other lengths permitted

• Boot: 1x SATA 240 GB

• Dimensions: 41.0 x 562.0 x 222.0 mm (1.7 x 22.2 x 8.8 inches)

• Maximum weight: 55 kg (121.2 lb)

Interconnect

• 1 or 2 CP–I–10 Interconnect switches

• 48x 10 Gb SFP+ fabric ports

• 6x 40 Gb QSFP+ fabric ports

• Dimensions: 438.4 x 473 x 43.4 mm (17.26 x 18.62 x 1.71 inches)

• Maximum weight: 8.95 kg (19.73 lb), with two installed PSUs

Management switch

Lenovo ThinkSystem NE0152T RackSwitch

Note:

A dedicated out-of-band management switch is required for this solution. If the Lenovo NE0152T is not used, you
must provide an out-of-band management switch with the correct configuration.

Chapter 1

ThinkAgile CP Overview

Summary of Contents for ThinkAgile CP 4000 Series





































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Upgrade Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands