manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 243

00

00000

00000

00000

000000

000000

000000

000000

00000

00000

00000

0000000

0000000

0000000

0000000

0000000

00

0

PCI
riser-card
assembly
(in long position)

Adapter

Adapter
connectors

PCI
riser-card
assembly
(in short position)

Adapter

Adapter
connectors

Full-length
adapter
bracket

Full-length
adapter
bracket

Figure 153. Adapter installation

Step 8.

Connect any required cables to the adapter (see “Internal cable routing and connectors” on page
179).

Attention:

• When you route cables, do not block any connectors or the ventilated space around any of

the fans.

• Make sure that cables are not routed on top of components under the PCI riser-card assembly.

• Make sure that cables are not pinched by the server components.

Step 9.

Replace the PCI riser-card assembly in the server (see “Replacing a PCI riser-card assembly” on
page 222).

Step 10. Perform any configuration tasks that are required for the adapter.

Step 11. Reinstall the cover (see “Replacing the cover” on page 196).

Step 12. Slide the server into the rack.

Step 13. Reconnect the power cords and any cables that you removed.

Step 14. Turn on the peripheral devices and the server.

Replacing an adapter in the rear two hard-disk-drive kit

Use this information to replace an adapter in the rear two hard-disk-drive kit.

You can only install SeveRAID-H1110 adapter in the rear two hard-disk-drive kit.

To install an adapter, complete the following steps:

Step 1.

Read the safety information that begins on “Safety” on page v and “Installation guidelines”
on page 34.

Step 2.

Turn off the server and peripheral devices and disconnect the power cords and all external cables.

Step 3.

Remove the cover (see “Removing the cover” on page 195).

Step 4.

Remove the rear two hard-disk-drive kit (see “Removing the rear two hard-disk-drive kit” on
page 224).

Step 5.

Follow the cabling instructions, if any come with the adapter. Route the adapter cables before
you install the adapter.

Chapter 6

.

Removing and replacing components

231

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands