Lenovo Moto One Hyper Service And Repair Manual Download Page 81

Page: 81 / 138

Lenovo Moto One Hyper
Level 2

– Service and Repair Manual

Lenovo Confidential Restricted:

PAGE 81

Do not share without consent from Lenovo

Front-Facing Camera Waterproof Bracket Assembly

Description

Reference #

Defender TPLCM Assy Etching ICE LATAM

Defender TPLCM Assy Etching SAN LATAM

Defender TPLCM Assy Etching TER LATAM

Defender TPLCM Assy Etching ICE EU

Defender TPLCM Assy Etching SAN EU
Defender TPLCM Assy Etching ICE APEM

Defender TPLCM Assy Etching TER APEM

Defender TPLCM Assy Etching ICE CN

Defender TPLCM Assy Etching TER CN

Defender TPLCM Assy Etching ICE RU
Defender TPLCM Assy Etching ICE BR

Defender TPLCM Assy Etching SAN BR

Defender TPLCM Assy Etching TER BR

Defender FRU TPLCM Front HSG Assy ICE

Defender FRU TPLCM Front HSG Assy SAN

Defender FRU TPLCM Front HSG Assy TER

HDW,BRKT,Defender,BRKT, waterproof, POP-

HDW,SCR,SCR, M1.0 x 0.20 x 1.4 Cross, BL

HDW,SCR,Screws M1.2x0.25 x 1.7, SLVR

SCR,SCREWS M1.4X0,3X3

Use fingers to place the Front-Facing Camera
Waterproof bracket on the Rear bucket aligning
with the pin on Waterproof Bracket with hole on
the Rear bucket as shown.

NOTE

Do not press or touch the middle part of the Front-
Facing Camera Waterproof bracket.

Use Torque Driver with Philips PH00 Bit to
tighten the two screw as shown (0.5±0.05 kgf-
cm).

Summary of Contents for Moto One Hyper











































































































































Search results

Summary of Contents for Moto One Hyper

Reviews:

Lenovo Moto One Hyper, Service And Repair Manual, Page: 81 / 138

Search results

Summary of Contents for Moto One Hyper

Reviews: