Lenovo Moto One Hyper Service And Repair Manual Download Page 137

Page: 137 / 138

Lenovo Moto One Hyper
Level 2

– Service and Repair Manual

Lenovo Confidential Restricted:

PAGE 137

Do not share without consent from Lenovo

IMEI Label Assembly

Description

Reference #

Defender TPLCM Assy Etching ICE LATAM

Defender TPLCM Assy Etching SAN LATAM

Defender TPLCM Assy Etching TER LATAM

Defender TPLCM Assy Etching ICE EU

Defender TPLCM Assy Etching SAN EU
Defender TPLCM Assy Etching ICE APEM

Defender TPLCM Assy Etching TER APEM

Defender TPLCM Assy Etching ICE CN

Defender TPLCM Assy Etching TER CN

Defender TPLCM Assy Etching ICE RU
Defender TPLCM Assy Etching ICE BR

Defender TPLCM Assy Etching SAN BR

Defender TPLCM Assy Etching TER BR

Defender FRU TPLCM Front HSG Assy ICE

Defender FRU TPLCM Front HSG Assy SAN

Defender FRU TPLCM Front HSG Assy TER

LBL,IMEI

Use the Plastic Tweezer to place the IMEI Label

on the SIM tray as shown.

Summary of Contents for Moto One Hyper











































































































































Search results

Summary of Contents for Moto One Hyper

Reviews:

Lenovo Moto One Hyper, Service And Repair Manual, Page: 137 / 138

Search results

Summary of Contents for Moto One Hyper

Reviews: