Lenovo C24-10 User Manual Download | Manualshive

Page: 11 / 33

background image

Chapter 1.

1-7

6. Insert the power cord into the monitor, then plug the monitor power cord and the computer

cord into grounded electrical outlets.

Note:

A certified power supply cord has to be used with this equipment. The relevant

national installation and or equipment regulations shall be considered. A certified power
supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC
60227 (designation H05VV-F 3G 0.75mm2 or H05VVH2-F2 3G 0.75mm2) shall be used.

Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation

H05RR-F 3G 0.75mm2 ) shall be used.

7. Power on the monitor and the computer.

8. When you install the monitor driver, download the driver that corresponds to your monitor

model from the Lenovo website http://www.lenovo.com/support/C24-10. Refer to the
“

“Manually installing the monitor driver”on page 3-5” section to install the driver.

«
...
9
10
11
12
13
...
»

Summary of Contents for C24-10


































Reviews:

No comments

Related manuals for C24-10

Brand: LaCie Pages: 4

Brand: Safety 1st Pages: 6

PDK 0212-OWG13L

Brand: IEE Pages: 10

Brand: Ssl Pages: 21

Brand: FDS Pages: 25

Brand: Hansol Pages: 14

Brand: Graco Pages: 32

Brand: Sentinel Pages: 11

Brand: NFREN Pages: 30

Brand: DoubleSight Pages: 53

Brand: I-Inc Pages: 19

SyncMaster P50FP

Brand: Samsung Pages: 105

Brand: AOC Pages: 28

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 1

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands