manualshive.com logo in svg

Lenovo 11CS000MCA, User Manual

Share
Download
Lenovo 11CS000MCA User Manual Download Page 70

3.  Install the coin-cell battery. 

4.  Reinstall all the removed parts. Then, reconnect the power cord and all disconnected cables to the 

computer.

5.  Reset the system date and time in the UEFI BIOS menu.

To dispose of the coin-cell battery, refer to the “Lithium coin-cell battery notice” in the 

Safety and Warranty 

Guide

.

Power supply assembly

Prerequisite

Before you start, read Appendix A “Important safety information” on page 71 and print the following 
instructions.

Before you open the computer cover, turn off the computer and wait several minutes until the computer is 
cool.

Although there are no moving parts in the computer after the power cord has been disconnected, the 
following warnings are required for your safety.

Keep fingers and other parts of your body away from hazardous, moving parts. If you suffer an injury, seek 
medical care immediately.Never remove the cover on a power supply or any part that has the following label 
attached. 

Hazardous voltage, current, and energy levels are present inside any component that has this label attached. 
There are no serviceable parts inside these components. If you suspect a problem with one of these parts, 
contact a service technician.

Replacement procedure

1.  Remove the computer cover. See “Computer cover” on page 44.

2.  Remove the front bezel. See “Front bezel” on page 45.

3.  Remove the drive bay assembly. See “Drive bay assembly” on page 48.

4.  Disconnect the power supply assembly cables from the system board.

64

M70t and M80t User Guide

Summary of Contents for 11CS000MCA

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands