background image

Low ESP Fan Coil Indoor Unit

3.2 Location for Installation 

(1) The appliance shall not be installed in the laundry. 

(2) 

The top holder must be strong enough to support unit’s weight. 

(3) Drain pipe can drain water out easily. 

(4) There is no obstacle at inlet or outlet. Please ensure good air circulation. 

(5) In order to make sure the space for maintenance, please install the indoor unit according 

to the dimension described below. 

(6) Keep the unit away from heating source, inflammable gas or smoke. 

(7) This is a concealed ceiling type unit. 

(8) Indoor unit, outdoor unit, power cord and electric wire should stay at least 1m from the TV 

set and radio. Otherwise, these electrical appliances may have image interference and 

noise. (Even if the distance is 1m, when there is strong electric wave, noise may still 

occur.) 

Fig 3.2 

Notes: 

Installation of the unit must be in accordance with National Electric Codes and local

regulations. 

Improper installation will affect unit’s performance, so do not install the unit by yourself.

Please contact local dealer to arrange professional technicians for the installation. 

Do not connect power until all installation work is finished.

3.3 Requirements for Communication Line 

Notes: 

If the unit is installed in the place with strong electromagnetic interference, shielded wire must 

be applied on the communication wire between indoor unit and wired controller. Twisted pair line 

with shielding function must be applied on the communication wire between indoor unit and indoor 

unit(outdoor unit). 

Summary of Contents for VRF VELD007N432U





























Reviews: