background image

3

SAFETY RULES FOR OPERATING 

YOUR FIREPLACE

  Use only IHP glass doors, specifically de-

signed for the Villa Vista™ fireplace.

  When cleaning the fireplace, the Ashes should 

be placed in a steel container with a tight 

fitting lid and moved outdoors immediately.  

Other waste shall not be placed in this con-

tainer. The closed container of ashes should 

be placed on a non-combustible floor or on 

the ground, well away from all combustible 

materials, pending final disposal. If the ashes 

are disposed of by burial in soil or otherwise 

locally dispersed, they should be retained in 

the closed container until all cinders have 

thoroughly cooled.

CAUTION: KEEP COMBUSTIBLE MA-

TERIALS AT LEAST 48 INCHES AWAY 

FROM THE FRONT OF THE FIREPLACE 

OPENING.

CAUTION: BURN UNTREATED WOOD 

ONLY.  OTHER MATERIALS SUCH AS 

WOOD PRESERVATIVES, METAL FOILS, 

COAL, PLASTIC, GARBAGE, SULPHUR OR 

OIL MAY DAMAGE THE CATALYST.

CAUTION: DO NOT OPERATE WITH-

OUT THE CATALYTIC COMBUSTOR IN 

PLACE.

CAUTION: NEVER BURN WITH THE 

BY-PASS OPENED ExCEPT FOR FIRE 

START-UP AND WHEN RELOADING THE 

STOVE.

TABLE OF CONTENTS

Safety Rules ......................................Page 2 

The Fireplace .....................................Page 3

Introduction ......................................Page 3

Parts Required  .................................Page 3

Additional Equipment (Optional) .......Page 3

Operating The Fireplace ....................Page 4

Fuel ...................................................Page 4

Catalytic Combustor ..........................Page 4

Combustion Control  .........................Page 4 

Starting And Maintaining A Fire ........Page 5

Refuelling For Best Performance ......Page 5

Smoking – Causes And 

  Troubleshooting ..............................Page 6

Important Notes ................................Page 6

Maintaining Your  

  Fireplace  .........................................Page 6

Creosote ............................................Page 6

Chimney Maintenance .......................Page 6

Dealing With A Chimney Fire .............Page 6

Catalytic Combustor ..........................Page 6

Door Frame Care ...............................Page 7

Refractory Replacement ....................Page 7

Door Installation ...............................Page 8

Door Adjustment ...............................Page 8

Glass Care - Replacement .................Page 8

Glass Care - Cleaning ........................Page 8

Gasket Replacement  ........................Page 8

FIREPlACE INSTAllATION  ..............Page 8

locating The Fireplace ......................Page 8

Framing, Facing And Mantel ..............Page 9

Hearth Extension Requirements  .......Page 9

Fireplace / Framing Dimensions ........Page 10

Insulated Chase Construction ...........Page 11

Nailing Flanges ..................................Page 11

Facing / Mantel  .................................Page 12

HOT AIR DUCTING INSTAllATION  ..Page 13

Gravity Kit .........................................Page 13

Outside Air Kit  ..................................Page 15

Chimney System ...............................Page 16

Acbi Chimney 

  Installation Instructions ..................Page 17

Offset Chimney Installation ...............Page 18

Angled Wall Radiation Shield ............Page 19

Chimney Support Installation ............Page 20

Chimney Chase And 

  Multiple Terminations......................Page 20

Masonry Applications .......................Page 21

Installation Accessories ....................Page 22

Replacement Parts ............................Page 23

Specifications ....................................Page 23

Clearance To Combustible  ................Page 23

Chimney Components lists ..............Page 24

Product Reference Information .........Page 26

THE FIREPLACE

INTRODUCTION

The Villa Vista fireplace is an energy efficient, 

heat circulating, close combustion fireplace 

using the catalytic technology.  You will receive 

a lifetime of comfort and enjoyment from your 

fireplace provided it is maintained and oper-

ated properly.

 Please read these instructions and retain 

this manual for future reference.

  Before beginning the fireplace installation, 

consult the local authorities to obtain your 

building permit and check your local building 

codes.  Install the fireplace only as described 

in these instructions and using only IHP 

components.

 

This fireplace has been tested for CAN/UlC 

S610-M87 and ANSI/Ul 127 under report 

number 192-5237.  It has also been tested 

for EPA 40 C.F.R Part 60, section 60.532(b).  

Certificate number 518.

  The Villa Vista Fireplace is not intended for 

use with a gas log set.  Failure to follow 

these instructions will void the certification 

and the warranty of the fireplace and may 

result in an unsafe installation.

Parts Required

  Fireplace model Villa Vista

  Door set (Black, Gold, Nickel)

  louver set (Del Sol, Diamante, luna, Fiori, 

Strada)

  7" diameter chimney

*

 model Secure 

Temp

®

 ASHT+, Secure Temp S-2100+ or 

ACBI manufactured by Security Chimneys 

International™ only, including:

 

- Chimney lengths

 

- Elbows (where necessary)

 

- Radiation shield, Attic radiation shield

 

- Roof flashing

 

- Rain cap 

 

- Support

  Outside air kit (included)

Additional Equipment (optional)

  Forced Air Kit 

u

  Gravity venting system

  Panel for clean face option 

 

(only with gravity venting system)

  Fireplace Blower Kit, UZY5

  Rigid Firescreen

  ACBI Chimney Outside Air Kit 

(required  

with ACBI chimney installation)

Not tested under EPA certification. If in-

stalled, this appliance no longer qualifies 

for EPA certification.

CONGRATULATIONS!

When you purchased your new fireplace, you joined the ranks of thousands of individuals 

whose answer to their home heating needs reflects their concern for aesthetics, efficiency 

and our environment. We extend our continued support to help you achieve the maximum 

benefit and enjoyment available from your new fireplace.

Thank you for selecting a IHP fireplace as the answer to your home supplemental heat-

ing needs.

*

Available from Security Chimneys™ 

Summary of Contents for VILLA VISTA 850028M



























Reviews: