Pre-Assembly I Stove Installation
Pre-Installation
1. After removing the packaging from the stove, lift the
hopper lid, and remove all pre-packaged items that
were shipped in the hopper. Next, open the stove
door and remove all pre-packaged items.
2. (Profile models only) Using a 7/16" socket or open
end wrench, remove the bolts which secure stove to
pallet. The bolts are located on the underside of the
wooden pallet.
Remove the Three Bolts from Underneath the Pallet
(Profile Models Only)
Installation Check List
It is strongly recommended that you have an Authorized
Dealer install your stove. If you install your stove your
self, you should review your installation plan with an
Authorized Whitfield or Traditions Dealer.
Check list:
Check off each item as you go through your installation
as part of the installation process.
□
Read the ENTIRE Stove Installation Section first
□
Read the Insert or Freestanding section (whichever
applies).
□
Determine the appropriate measurements and loca
tions for yot:Jr installation.
□
Follow the general installatioh -di�tions under
Stove Installation and the installation section appro
priate to your stove.
□
Be sure to pre-fit all items before you install, fasten,
or set up the stove permanently.
Prior to lighting your stove:
□
Review the Safety Precautions section.
□
Review the Pellet Fuels Section.
□
Review the Operating Instructions.
□
Follow the Operating Instructions.
After you have begun operation of your stove:
□
Review the Routine Cleaning / Maintenance infor
mation.
□
Enjoy the warmth from your new Whitfield or Tradi
tions Pellet Stove!
All Models - Plug power cord into connector on Unit
Plug the power cord connector into the corresponding con
nector on the back of appliance. (Profile 30 Insert - Route
power cord behind side shroud panel).
Profile 30 Insert - Installing Leveling Bolts
It may be necessary to level the appliance in some in
stallations such as a recessed firebox floor (if the exist
ing fireplace has a firebox floor which is lower than the
hearth}. If needed, install the 2 leveling bolts (1/4-20 x 3"
long) into the threaded holes at the rear base of the in
sert. Adjust bolts until appliance is level.
Profile 30 Insert - Installing Shroud Assembly
(To be done after venting system is installed)
This appliance comes with a set of metal panels that seal the
fireplace opening when fitted together. There is also a trim
assembly that frames the shroud assembly to give
.
it an at
tractive finished appearance. Put the shroud assembly to
gether according to the following instructions (Ref. see Illus
tration on page 37).
1. Remove panels from package.
2. Open the hopper lid on insert so it is out of the way for
when panels are installed.
3. Install the control board onto the right side panel (with
door) using the TEK screw (#8 x ½") provided.
4. Position the power cord so that it will be behind either
the right or left side shroud panel when they are in
stalled.
Page 7
5. Install right side shroud panel onto right side of insert body
by sliding the 2 flanges on side of panel into correspond
ing slots on insert.
6. Connect the wiring harness from insert into corresponding
connector on control board.
7. Locate damper rod on left side of insert. Rotate angled
arm of rod so it is pointing down. Remove damper knob
and set aside.
8. Install the left-hand panel onto the left side of insert
body by sliding the 2 flanges on side of panel into corre
sponding slots on insert.
9. Reach behind left shroud panel and rotate damper
arm so that end is inserted into the upper right hand
slot of left shroud panel (see illustration on page 9,
bottom of left-hand column).
10. Reinstall damper knob by threading it onto end of
damper rod.
11. Set the top shroud panel in place over the two side
panels. Position the 2 tabs on bottom of top shroud
panel so they slide into corresponding clips on in
sert. Connect the top shroud panel to the side pan
els by pressing pins from side panels into corre
sponding holes on top panel.
12. Remove the shroud trim from its packaging. As
semble it together using the corner keys ("L" shaped
brackets) provided. Slide assembled trim over the
top shroud panel and slide it down over the side
panels.
13. Push insert back into place so the shroud is flush
with the face of the hearth.
