background image

2

LENNOX HEARTH PRODUCTS  •  MERIT PLUS

®

 B-VENT GAS FIREPLACES (MPB33/35/40/45)  •  INSTALLATION INSTRUCTIONS

PACKAGING

The assembled vented gas fireplace is pack-

aged with:

  (1 set) Logs (packaged in a carton inside 

the firebox).

  (1 bag) Volcanic Stone (included in the 

firebox or bottom compartment).

  (1 bag) Glowing Embers (in bottom compart-

ment).

  Literature Kit (envelope in bottom com-

partment containing Care and Operation 

Instructions, Installation Instructions, 

Safety-In-Operation Warning Labels, War-

ranty).

  (1) Hood (behind the top louver assembly).

INTRODUCTION 

The 

Millivolt

 appliances have a millivolt gas 

control valve with piezo ignition system. If any 

optional accessories that will require electrical 

power are to be installed, the electrical power 

must be provided at the time of appliance in-

stallation. 
The 

Electronic

 appliances are designed to op-

erate on natural or propane gas. An electronic 

intermittent pilot ignition system provides safe, 

efficient operation. External electrical power is 

required to operate these units. In the event of a 

power outage, four (4) "AA" batteries (in battery 

holder) provide backup power for appliance 

operation (excluding [optional] blower).

APPROVED VENT COMPONENTS

These vented gas fireplaces are designed for 

residential applications. They must be installed 

with approved Type-B, double wall vent pipe 

systems and a listed vent termination routed 

to the outside atmosphere. Use only the proper 

size listed below.

REqUIRED PIPE DIAMETER:

MPB33 series: 

Requires 4" (102 mm)

MPB35 series: 

Requires 5" (127 mm)

MPB40 series: 

Requires 5" (127 mm)

MPB45 series: 

Requires 6" (152 mm)

       

WARNING

B-Vent appliances are not 

designed to operate in negatively 

pressured environments (pres-

sure within the home is less than 

pressures outside). Significant 

negatively pressured environ-

ments caused by weather, home 

design, or other devices may 

impact the operation of these 

appliances.  Negative pres-

sures may result in poor flame 

appearance, sooting, damage to 

property and/or severe personal 

injury. Do not operate these 

appliances in negatively pres-

sured environments.

TABLE OF CONTENTS 

Packaging .................................................... 2
Introduction ................................................. 2
General Information ..................................... 2
Requirements for the 
   Commonwealth of Massachusetts ............ 4
Cold Climate Insulation ................................ 4
Manufactured Housing ................................. 4
Location ........................................................5
Vent Termination Clearances  ....................... 5
Appliance and Vent Clearances .................... 6
Pre-Installation Steps ................................... 7
Typical Installation Sequence  ...................... 7
Detailed Installation Steps ............................ 7
Step 1. Framing ............................................ 7
   Framing Specifications ................................ 8
   Fireplace Specifications .............................. 9
Step 2. Routing Gas Line ............................. 9
Step 3. Installing Vent System ................... 10
Step 4.  Field Wiring ................................... 11
Step 5.  Wiring Optional 
             Forced Air Blower Kit .................... 12
Step 6.  Connecting Gas Line ..................... 12
Step 7.  Installing Optional Outside Air Kit ..13
Step 8.  Verifying Appliance Operation ........... 14
Step 9.  Installing Volcanic Stone, Glowing 
             Embers, and Logs  ........................ 14
Step 10. Removing and 
              Installing the Glass Door  ............. 19
Step 11. Burner Adjustments ..................... 19
Step 12. Testing Vent Operation ..................21
Step 13. Hood Installation .......................... 21
Step 14. Finishing Requirements ............... 21

Step 15. Attaching Safety-in-Operation 

                Warnings ............................ 22
Gas Conversion Kits ......................... 23

Please read and understand these 

instructions before beginning your 

installation.

 

       WARNING 

Young children should be care-

fully supervised when they are 

in the same room as the appli-

ance. Toddlers, young children 

and others may be susceptible 

to accidental contact burns. A 

physical barrier is recommended 

if there are at risk individuals in 

the house. To restrict access to 

a fireplace or stove, install an 

adjustable safety gate to keep 

toddlers, young children and 

other at risk individuals out of 

the room and away from hot 

surfaces.

       AVERTISSEMENT 

Les jeunes enfants devraient être 

surveillés étroitement lorsqu’ils 

se trouvent dans la même pièce 

que l’appareil. Les tout petits, 

les jeunes enfants ou les adultes 

peuvent subir des brûlures s’ils 

viennent en contact avec la sur-

face chaude. Il est recommandé 

d’installer une barrière physique 

si des personnes à risques habi-

tent la maison. Pour empêcher 

l’accès à un foyer ou à un poêle, 

installez une barrière de sécu-

rité; cette mesure empêchera les 

tout petits, les jeunes enfants et 

toute autre personne à risque 

d’avoir accès à la pièce et aux 

surfaces chaudes.

GENERAL INFORMATION

Children and adults should be alerted to the 

hazards of high surface temperature and 

should stay away to avoid burns or clothing 

ignition. 

Les enfants et les adultes devraient être 

informés des dangers que posent les 

températures de surface élevées et se 

tenir à distance afin d’éviter des brûlures 

ou que leurs vêtements ne s’enflamment.

DO NOT ATTEMPT TO ALTER OR MODIFY 
THE CONSTRUCTION OF THE APPLIANCE 
OR ITS COMPONENTS. ANY MODIFICATION 
OR ALTERATION MAY VOID THE WARRANTY, 
CERTIFICATION AND LISTINGS OF THIS UNIT.

Summary of Contents for MPB33CNE

























Reviews: