background image

23

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

LENNOX HEARTH PRODUCTS  •  MERIT PLUS

®

 B-VENT GAS FIREPLACES (MPB33/35/40/45)  •  INSTALLATION INSTRUCTIONS

Millivolt SIT Systems

Propane Gas to Natural Gas

Conversion Kits

Models

Cat. No.

MPB33

H8849

MPB35

H8850

MPB40

H8851

MPB45

H8852

Millivolt SIT Systems

Natural Gas To Propane Gas

Conversion Kits

Models

Cat. No.

MPB33

H2009

MPB35

H2011

MPB40

H2013

MPB45

H2015

Electronic

 SIT Systems

 Propane Gas To Natural Gas

Conversion Kits

Models

Cat. No.

MPB33

H8845

MPB35

H8846

MPB40

H8847

MPB45

H8848

In Canada:

THE CONVERSION SHALL BE CAR-

RIED OUT IN ACCORDANCE WITH THE 

REqUIREMENTS OF THE PROVINCIAL 

AUTHORITIES HAVING JURISDICTION 

AND IN ACCORDANCE WITH THE RE-

qUIREMENTS OF THE CAN/CGA-B149.1 

INSTALLATION CODE.

LA CONVERSION DEVRA ÊTRE 

 EFFECTUéE CONFORMéMENT AUX 

RECOMMANDATIONS DES AUTORI-

TéS PROVINCIALES AYANT JURIDIC-

TION ET CONFORMéMENT AUX EXI-

GENCES DU CODE D'INSTALLATION 

CAN/CGA-B149.1.

Gas conversion kits are available to adapt your 

appliance from the use of one type of gas to 

the use of another. These kits contain all the 

necessary components needed to complete the 

task including labeling that must be affixed to 

ensure safe operation.

Kit part numbers are listed here and the follow-

ing steps detail the conversion procedure. Refer 

to the instructions provided with the conversion 

kit when performing any gas conversion.

GAS CONVERSION KITS

ATTENTION: AVANT D’EFFECTUER 

LA CONVERSION, COUPEz D’ABORD 

L’ALIMENTATION EN GAz, ENSUITE, 

COUPEz L’ALIMENTATION éLECTRIqUE.

Step 2.

 Open the lower control compartment 

door (see 

Figure 22 on Page 13

) by pushing 

on the right top corner of the door (the door is 

hinged at the bottom).

[Optional] Remove the control compartment 

door by sliding the hinge pin, located at the 

door’s left side, to the right until it disengages 

from the left corner post hole. Pull the control 

compartment door diagonally to the left, away 
from the fireplace.

Step 3.

  Remove the front glass door/frame 

from the appliance (see 

Page 19

).

Step 4.

 Carefully remove the logs. 

Exercise 

care so as not to break the logs

.

Step 5.

 Refer to 

Figures 28, 29, or 30

A.

 Remove the grate and sub floor.

B.

 Remove the two (2) screws securing the 

burner assembly.

C.

 Remove the burner assembly with attached 

venturi tube.

MILLIVOLT AND ELECTRONIC IGNITION 

SYSTEM APPLIANCES
Step 1.

 

SIT Systems

 - Refer to 

Figure 38

 and 

the instructions provided with the SIT Regu-

lator Conversion Kit. Using a Torx T20 driver 

to remove and discard the pressure regulator 

mounting screws (two screws for electronic 

models, three screws for millivolt models), 

pressure regulator tower, the diaphragm as-

sembly (if applicable) and the spring. Discard 

all removed components.

Electronic

 SIT Systems

Natural Gas To Propane Gas

Conversion Kits

Models

Cat. No.

MPB33

H8632

MPB35

H8634

MPB40

H8636

MPB45

H8638

            

WARNING

This conversion kit shall be installed by a qualified service agency in 

accordance with the manufacturer’s instructions and all applicable codes 

and requirements of the authority having jurisdiction. If the information in 

these instruction is not followed exactly, a fire, explosion or production of 

carbon monoxide may result causing property damage, personal injury 

or loss of life. The qualified service agency is responsible for the proper 

installation of this kit. The installation is not proper and complete until the 

operation of the converted appliance is checked as specified in the manu-

facturer’s instructions supplied with the kit. The qualified service agency 

performing this installation assumes responsibility for this conversion.

            

AVERTISSEMENT

Cette trousse de conversion doit être installée par un technicien agréé, 

selon les instructions du fabricant et selon toutes les exigences et tous les 

codes pertinents de l’autorité compétente. Assurez-vous de bien suivre 

les instructions dans cette notice pour réduire au minimum le risque 

d’incendie, d’explosion ou la production de monoxyde de carbone pouvant 

causer des dommages matériels, des blessures ou la mort. Le tecnicien 

agréé est responsable de l’installation de cette trousse. L’installation n’est 

pas adéquate ni complète tant que le bon fonctionnement de l’appareil 

converti n’a pas été vérifié selon les instructions du fabricant fournies avec 

la trousse. Le fournisseur de service qualifié ayant réalisé l'installation 

assume les responsabilités liées à la conversion.

INSTALLATION INSTRUCTIONS

Step 1.

 

TURN OFF THE GAS SUPPLY TO THE 

APPLIANCE and disconnect power supply at 

the circuit breaker. Ensure appliance is cold. 

CAUTION: THE GAS SUPPLY SHALL BE 

SHUT OFF PRIOR TO DISCONNECTING THE 

ELECTRICAL POWER, BEFORE PROCEEDING 

WITH THE CONVERSION.

Summary of Contents for MPB33CNE

























Reviews: