Lennox iHarmony Zone Thermostat Installation And Setup Manual Download Page 13

Page: 13 / 16

Table 4. Alert Codes

Error

Code

Message

Type

Condition and

Email Notification

Description

Thermostat Display

Text

System Action

Action to Clear /

Recovery Condition

551

Critical

Lost communication

Problem (Zoning

Control)

A pop-up display will

appear indicating

communication

error.
Indoor temp is

displayed as “--” on

the home screen.

inside

When any zone

sensor loses

communication with

the damper control

module, the entire

system will go into

central mode.

Once communication is

reestablished the device

will return to normal zone

operations.
Any lost communication

between the zone sensor

and damper control module

will result in the applicable

error code being displayed

542, 543, 544 or 545 at the

thermostat.
Check wiring between

damper control module and

the zone sensor reporting

error code 551.

Summary of Contents for iHarmony Zone Thermostat

















Search results

Summary of Contents for iHarmony Zone Thermostat

Reviews:

Related manuals for iHarmony Zone Thermostat

Brands by name

Popular brands

Lennox iHarmony Zone Thermostat, Installation And Setup Manual

Search results

Summary of Contents for iHarmony Zone Thermostat

Reviews:

Related manuals for iHarmony Zone Thermostat

Brands by name

Popular brands