manualshive.com logo in svg

Lennox iHarmony 17A30, Installation And Setup Manual

Share
Download
Lennox iHarmony 17A30 Installation And Setup Manual Download Page 9

9

Alert Codes

Table 4. Alert Codes

Error 

Code

Message 

Type

Condition and 

Email Notification 

Description

Thermostat Display 

Text

System Action

Action to Clear / 

Recovery Condition

542

Critical

Temperature Sensor 

Error

Problem (Zoning 

Control)

Indoor temp is displayed 

as “--” on the home 

screen.

inside

0

1

Anytime there is a zone 

sensor temperature 

sensor error or  any 

zone sensor loses 

communication with the 

damper control module, 

the entire system will go 

into central mode.

Error could be due to either a 

temperature sensor error or lost 

communication between zone 

sensor and damper control module.
If problem is due to temperature 

sensor issue, then zone sensor 

will need to be replace. If sensor 

auto corrects itself the alert will 

be automatically cleared and 

system will return to normal zone 

operations.
Error codes 542, 543, 544 and 

545 could also be caused by lost 

communication with the damper 

control module. If this is the case, 

most likely an error code 551 is 

being displayed at the applicable 

zone sensor.
Check wiring between damper 

control module and the zone 

sensor reporting error code 551.

NOTE: 

If error is due to lost 

communication 551, 

error notification 542, 

543, 544 and 545 will 

only be displayed at the 

thermostat.

543

Temperature Sensor 

Error

Problem (Zoning 

Control)

544

Temperature Sensor 

Error

Problem (Zoning 

Control)

545

Temperature Sensor 

Error

Problem (Zoning 

Control)

Summary of Contents for iHarmony 17A30













Reviews:

No comments

Brands by name

Popular brands

Load more brands