manualshive.com logo in svg

Lennox iHarmony 17A30, Installation And Setup Manual

Share
Download
Lennox iHarmony 17A30 Installation And Setup Manual Download Page 2

2

Tables of Contents

Shipping and Packing List ....................................2

Electrical Characteristics ......................................3

Dimensions ...........................................................3

Unit Dimensions (H x W x D) .............................................. 3

Wall Plate Dimensions (H x W) ........................................... 3

Installation Guide ..................................................3

Installation Considerations .................................................. 3

Unpacking Zone Sensor and Determining Best Location ... 4

Installing Zone Sensor ........................................................ 4

Zone Sensor Terminal Information ...................................... 6

Connecting Zone Sensor Wiring ......................................... 6

Install Zone Sensor to Backplate ........................................ 8

Setup Guide..........................................................8

Apply Power ........................................................................ 8

Menu > Advanced Settings ................................................. 8

Installer Checklist ...............................................12

Shipping and Packing List

Item

Quantity

Zone sensor with backplate attached

1

Wall plate

1

Mounting screws (M3.5x25mm self-tapping screws)

2

Wall anchors

2

Warranty sheet

1

Installation and setup guide

1

User guide

1

WARNING

Improper installation, adjustment, alteration, ser­

vice or maintenance can cause property damage, 

personal injury or loss of life.
Installation and service must be performed by a li­

censed professional HVAC installer (or equivalent) 

or a service agency.

The 17A30 Zone Sensor can be used in systems 

controlled by any Lennox communicating thermostat.
The 17A30 zone sensor can also be used in 

combination with the 10C17 In­Zone thermostat.

Summary of Contents for iHarmony 17A30













Reviews:

No comments

Brands by name

Popular brands

Load more brands