manualshive.com logo in svg

Lennox iHarmony 17A30, Installation And Setup Manual

Share
Download
Lennox iHarmony 17A30 Installation And Setup Manual Download Page 3

3

CAUTION

This is a 12VDC low­voltage zone sensor. Do not 

install on voltages higher than 14VDC.

Electrical Characteristics

All values are at 77°F (25°C). This unit does employ 

mis­wire circuit protection.

Table 1. Zone Sensor Power Requirements

Min

Nom

Max

Unit

Input  

Voltage

10

12

14

VDC

Input 

Current

-

61.5

133

mA

WARNING

Always turn off power at the main power source 

by switching the circuit breaker to the OFF 

position before installing or removing this zone 

sensor.
All wiring must conform to local and national 

building and electrical codes and ordinances.

Dimensions

U

nit

 D

imensions

 (H 

x

 W 

x

 D)

Dimensions: 3­5/16 x 4­5/16 x 7/8 in. (84 x 110 x 

22mm)

W

all

 P

late

 D

imensions

 (H 

x

 W)

Dimensions: 4­1/2” x 5­3/4” (114 x 146mm)

Installation Guide

i

nstallation

 C

onsiDerations

The 17A30 zone sensor is a 12VDC low­voltage 

device and requires a common wire to the damper 

control module to operate.

•  Shut off all power to system components before 

installing zone sensor

•  Make sure that all wiring conforms to local 

and national building and electrical codes and 

ordinances

•  Never install the zone sensor on outside walls or 

in direct sunlight

Summary of Contents for iHarmony 17A30













Reviews:

No comments

Brands by name

Popular brands

Load more brands