background image

Page 28

Troubleshooting

LIMIT SWITCH WATCHĆ

GUARD MODE. GAS

VALVE OFF. COMB. AIR

INDUCER OFF. INDOOR

BLOWER OFF WITH

DELAY. LED#1-SLOW

FLASH LED#2 - ON. IS

60MINUTE RESET 

PERIOD COMPLETE?

NORMAL HEATING MODE

ABNORMAL HEATING MODE

FLAME RECTIFICATION CURRENT

CHECK. CAN FLAME BE PROVEN WITHIN

4 SECONDS AFTER GAS VALVE OPENS?

(

u

0.15 microamps)

FLAME PRESENT?

INDOOR BLOWER ON DELAY BEGINS

(45 seconds.)

PRIMARY AND SECONDARY LIMIT

SWITCHES CLOSED?

COMBUSTION AIR PRESSURE

SWITCH CLOSED?

LOW FLAME SIGNAL

(Does not affect operation of control)

LED #1 -- SLOW FLASH

LED #2 -- FAST FLASH

GAS VALVE DE-ENERGIZED.

COMBUSTION AIR INDUCER

DE-ENERGIZED. INDOOR BLOWER

ON UNTIL SWITCH CLOSES.LED #1

-- SLOW FLASH. LED #2 -- ON.

IS LIMIT SWITCH CLOSED?

GAS VALVE DE-ENERGIZED.

COMBUSTION AIR INDUCER ON.

INDOOR BLOWER OFF WITH DELAY

LED #1 -- OFF. LED #2 -- SLOW FLASH.

HAS CAB SWITCH CLOSED IN 2.5 MINUTES?

15ĆSECOND COMBUSTION AIR INDUCER PREPURGE

INITIATED BY CLOSED PRESSURE SWITCH.

YES

IGNITOR WARMĆUP -- 20 SECONDS.

YES

4ĆSECOND TRIAL FOR IGNITION.

GAS VALVE OPENS. IGNITOR IS ENERGIZED

YES

FLAME STABILIZATION PERIOD.

GAS VALVE OFF. COMBUSTION AIR INDUCER ON.

INDOOR BLOWER OFF.

HAS CONTROL FAILED TO SENSE FLAME FOR

FIVE CONSECUTIVE TRIES DURING A SINGLE

HEAT DEMAND?

IGNITION WATCHGUARD MODE. GAS VALVE OFF.

COMBUSTION AIR INDUCER OFF.

INDOOR BLOWER OFF WITH DELAY

LED 1 ALT. SLOW FLASH LED 2 ALT SLOW FLASH

IS 60ĆMINUTE RESET PERIOD COMPLETE?

YES

4 SECONDS

YES

HAS CONTROL RESET IGNITION

SEQUENCE FOUR TIMES?

FLAME SIGNAL ABOVE 0.7 MICROAMPS?

YES

YES

HAS PRIMARY/SECONDARY LIMIT

RESET (CLOSED) WITHIN 3

MINUTES?

YES

ROLLOUT SWITCH CLOSED?

GAS VALVE POWER OFF. 

COMBUSTION AIR INDUCER POWER OFF.

INDOOR BLOWER OFF WITH DELAY

LED #1 -- ON. LED #2 -- SLOW FLASH.

SEQUENCE HOLDS UNTIL ROLLOUT SWITCH IS RESET

YES

THERMOSTAT DEMAND SATISFIED.

LED #1 & #2 SIMULTANEOUS SLOW FLASHES.

COMB. AIR INDUCER CONTINUES 5ĆSECOND

POST PURGE AFTER T'STAT DEMAND IS SATISFIED.

INDOOR AIR BLOWER COMPLETES SELECTED OFF"

DELAY BEFORE SHUTTING OFF.

YES

NO

5ĆMINUTE PRESSURE SWITCH

WATCHGUARD MODE.

YES

IS THERE A PROPER GROUND?

IS VOLTAGE ABOVE 75 VOLTS?

IS IGNITOR INTACT AND CONNECTED?

LEDS SIGNAL 

ALTERNATING

FAST FLASH

NO

YES

YES

YES

YES

YES

NO

NO

NO

NO

NO

NO

NO

NO

YES

YES

NO

NO

NO

NO

YES

YES

YES

YES

Downloaded from 

ManualsNet.com

 search engine

Summary of Contents for G26 Series
































Reviews: