background image

Page 12

Venting

General Requirements

These instructions should be used as a guideline and do
not supersede local codes in any way. 
Install vent accord-
ing to local codes, these instructions, the current National
Fuel Gas Code (ANSI-Z223.1) in the USA or the current
standards of CAN/CGA-B149.1 and -B149.2 in Canada.

This gas fireplace is equipped with a concentric vent col-
lar for ease of installation. The concentric vent pipe will
bring in outdoor air for combustion and will remove ex-
haust gases. Vent terminations are ordered separately.

This Lennox gas fireplace is for use only with Lennox
approved concentric vent pipe: rigid vent pipe in vertical
venting applications, and rigid or flexible vent pipe in
horizontal applications. Each vent must be terminated
using a Lennox vent termination. Approved venting kits
and components are listed on page 26 of this manual.

NOTE - The vent terminations are certified for use
with this unit and must be installed without modifica-
tion.

WARNING

All vent system connections/joints must be properly
sealed using only Lennox MILL-PAC BLACK HIGH
TEMPERATURE SEALANT, Catalog Number 10K81.
Failure to properly seal the vent system could allow
carbon monoxide leakage resulting in injury or death.

Sealing and Joining Rigid Vent Pipe

Apply only Lennox MILL-PAC BLACK HIGH TEM-
PERATURE SEALANT 
(Catalog number 10K81)
around outside of inner and outer vent collars before
assembling vent to collar. Outer pipe must also be se-
cured to outer collar using three sheet metal screws.
See figure 11. Sealant must be applied to all rigid pipe
joints and the outer pipe must be secured with three
sheet metal screws.

SECURING RIGID VENT PIPE TO COLLAR

USE THREE SCREWS TO

SECURE OUTER VENT

PIPE TO OUTER COLLAR

APPLY ONLY LENNOX MILL-PAC BLACK HIGH
TEMPERATURE SEALANT (Catalog No. 10K81)

AND SLIDE RIGID PIPE OVER INNER AND

OUTER COLLARS.

NOTE - The bottom part of

the outer pipe is omitted in

order to show the detail of

the inner pipe.

RIGID VENT

PIPE

FIGURE 11

Sealing and Connecting Flexible Vent Pipe

Flexible vent pipe is packaged and shipped in its con-
tracted state. When installing flexible vent pipe, its length
may be expanded to twice its contracted size. You should
expect to extend a 3 ft. section of flexible pipe up to 6 ft.

IMPORTANT

Under no circumstances, may separate sections of
concentric flexible vent pipe be joined together.

When flexible vent pipe is used, both inner and outer
pipes should be secured to the fireplace concentric
collar and to the vent termination using only Lennox
MILL-PAC BLACK HIGH TEMPERATURE SEALANT
(Catalog number 10K81) and metal gear clamps as
shown in figure 12.

SECURING VENT PIPE TO COLLAR

FLEXVENT

OUTER

COLLAR

GEAR

CLAMPS

HOLES PROVIDE

SCREWDRIVER ACCESS
FOR TIGHTENING INNER

GEAR CLAMP.

APPLY ONLY LENNOX MILL-PAC

BLACK HIGH TEMPERATURE
SEALANT (Catalog No. 10K81)

AND SLIDE FLEXIBLE PIPE OVER

INNER AND OUTER COLLARS.

NOTE - Part of the outer

pipe is pulled away to show

the detail of the inner pipe.

FIGURE 12

Summary of Contents for DR3025



























Reviews: