Lennox ComfortSense 8500 Series Installation And Setup Manual Download Page 20 | Manualshive

Page: 20 / 28

background image

20

Table 5. System Status Descriptions

State (Icon)

Icon Location

Description

Home Screen

When either of following error occur, this icon would

be displayed.

•  Some RTU compr. Locked
•  All RTU compr. Locked
•  RTU fault state - fault detected
•  CS fault state - fault detected

Home Screen

Display during smooth setback recovery (SSR)

execution.

Technician Status

Screen

There are communication errors.

Technician Status

Screen

Lost communications with host.

Technician Status

Screen

There are no communication errors.

Technician Status

Screen

When RTU state is warm-up mode coming out of an

unoccupied state, this icon will be displayed.

Technician Status

Screen

When RTU state is cool-down mode coming out of

an unoccupied state, this icon will be displayed.

«
...
18
19
20
21
22
...
»

Summary of Contents for ComfortSense 8500 Series





























Reviews:

No comments

Related manuals for ComfortSense 8500 Series

Brand: Daikin Pages: 46

Brand: Hanna Instruments Pages: 11

Brand: Home Automation Pages: 19

Brand: VDH Pages: 8

Brand: RF Tech Pages: 2

Brand: Bryant Pages: 22

Radio wall thermostat

Brand: Hummel Pages: 72

Brand: Hama Pages: 10

Raychem RAYSTAT-EX-02

Brand: nvent Pages: 20

Brand: Seltron Pages: 34

Brand: tado° Pages: 16

Brand: Taco Pages: 4

Redi Chek ET-81

Brand: Maverick Pages: 1

Brand: Viesta Pages: 28

Brand: Kermi Pages: 100

Brand: Schluter Systems Pages: 76

Brand: Carrier Pages: 13

Brand: Carrier Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands