manualshive.com logo in svg

Lennox ComfortSense 8500 Series, Installation And Setup Manual

Share
Download
Lennox ComfortSense 8500 Series Installation And Setup Manual Download Page 19

19

System Status Descriptions

The system status screen icons can be access by pressing the 

···

 (three dots) which is located on the left 

side of the home screen. Then press the view status option. 

Press the red toolbox to access the technician system status screen. Technician pin 864 is required to 

access that screen.

NOTE: 

The technician pin cannot be changed.

Table 5. System Status Descriptions

State (Icon)

Icon Location

Description

Home Screen

When current RTU function is heating, this icon will 

be displayed.

Home Screen

When current RTU function is cooling, this icon will 

be displayed.

Home Screen

When current RTU function is dehumidifying, this 

icon will be displayed.

Home Screen

When fan operation was set to auto, if blower of 

RTU is ON, this icon will be displayed.

Home Screen

When fan operation was set to on, if RTU blower is 

ON, this icon would be displayed.

Home Screen

This icon is displayed on the screen in CO

2

 mode. If 

display function is turned on

Summary of Contents for ComfortSense 8500 Series





























Reviews:

No comments

Brands by name

Popular brands

Load more brands