background image

Page 9

Table 7. 

Seven-Segment  Status Display

Operation

Description

Idle Mode:

Decimal point blinks at 1 Hz 

Decimal point blinks at 1 Hz (0.5 second on, 0.5 second off). Display OFF.

Soft Disabled

Top & Bottom horizontal line and decimal point blink at 1 

Hz

Top & Bottom horizontal line and decimal point blink at 1 Hz (0.5 second on, 0.5 sec-

ond off). See additional information below this table.

OEM Test Mode

All segments flashing at 2 Hz  (unless error is detected)

Electrical Heating stage

Shows number of currently active electric heat pilot relays.

Following string is repeated if one stage Heat is active with 850 CFM:
H 1 pause A 8 5 0 pause

Cooling Stage

Shows what stage of cooling is currently operating.

Following string is repeated if second stage cooling is active with 1235 CFM: 
C 2 pause A 1 2 3 5 pause

Heat Pump Stage

Shows what stage of heat pump is currently operat ing.

Following string is repeated if first stage heat pump is active with 925 CFM and no 

Electri cal  Heat:
h 1 pause H 0 pause A 9 2 5 pause

Heat pump & electrical heating stage

Shows current heat pump operating stage and number of 

active electric heat pilot relays.

Following string is repeated if one stage electrical heat and second stage heat pump is 

active with 600 CFM:
h 1 pause H 1 pause A 1 6 5 0 pause

Defrost Mode

Shown only while in an active defrost. (Simultaneous Y, W, 

and O)

Following string is repeated if defrost is active with two electrical heat stages active 

and 975 CFM:
d f pause H 2 pause A 9 7 5 pause

Dehumidification mode

Shows that the unit is providing dehumidification in 

 

stead of straight cooling.

Following string is repeated if dehumidification is active with 685 CFM:

d pause A 6 8 5 pause

Indoor Blower only (G demand)

Shows the current CFM delivery of the main blower in 

actual CFM.

If indoor blower is providing 1600 CFM: following string is repeated:
A 1 6 0 0 pause

Diagnostic recall

Shows the last 10 stored diagnostic error codes. Ini tiated 

by a 2-second button press. Button press inter rupts the 

current display pattern. After all codes are displayed, 

current display status will resume opera tion.

If first error is 250, second 231:

E pause 2 5 0 pause E pause 2 3 1
Next codes (up to 10) are show using same method.
If there is no error codes stored:
E pause 0 0 0

Fault Memory clear

After the fault memory is cleared following string is displayed with 0.5 seconds charac-

ter on/off time:
0 0 0 0 pause

Active Error in AHC Idle mode

Shown all active error(s) codes

Following string is repeated if Error E125 and E201 are present:
E1 2 5 pause E 2 0 1

Active Error in Run Mode

Shown current status and all active error(s) codes

Following string is repeated if Error E311 is present while blower aped at 880CFM:
A 8 8 0 pause E 3 1 1

Discharge Air Temperature Sensor (DATS)

Any time DAT is sensed in operating range value is dis-

played if indoor blower is running.

Following string is repeated if three stage el. heat is active with 850 CFM & DAT is 

104° F:
H 3 pause A 8 5 0 pause U 1 0 4 pause

Soft Disable

Steps to follow if the damper control module is displaying the soft disable code:
1. 

 Confirm  proper  wiring  between  all  devices 

(Thermostat, damper control module, 

indoor and outdoor)

2.   Cycle power to the control that is displaying the soft disable code.
3.  Put the room thermostat through Set Up.
4.   Go  to 

setup / system devices / thermostat / edit / push reset

.

5.   Go  to 

setup / system devices / thermostat / edit / push resetAll.

Summary of Contents for 16B27

























Reviews: