Lennox 100017 Manual Download Page 33

Page: 33 / 52

Table 2. Alert Codes and Troubleshooting

GF= Gas Furnace, AH=Air Handler, ID=Indoor unit (GF or AH), HP=Heat Pump, AC=Air Conditioner, OD=Outdoor Unit (AC or HP), PA=Pure Air S, ZA=Zone system and TS=Thermostat

Alert

Code

Inverter

Flash

Code

Priority

Condition

Actual Displayed

Alert Text

Under dealer

control center >

Notifications

Component or System Operational State and Troubleshooting Tip

How to clear alert code

430

Service

Soon/Service

Urgent

OD Inverter

Compressor

Startup Fail

Compressor start-up failure.
• If condition is detected, outdoor unit will stop (compressor and fan) – service soon condition.

• Anti-short cycle is initiated.

•

If condition occurs 10 times within 60 consecutive minutes, the system will lockout – service

urgent condition.

•

Inverter LEDs will flash code 26.

• Refer to the unit service documentation for detailed troubleshooting procedures.

Inverter flash code 26.

The sequence is:
•

Red LED: Two Flashes

•

Green LED: Six Flashes

NOTE:

Inverter normal operations with no error code present is as follows. Red LED is ON and

Green LED is OFF.

•

Check refrigerant

• Replace outdoor control board
• Replace inverter.

To clear, disconnect power to outdoor unit

and restart.

431

Service

Soon/Service

Urgent

OD Inverter PFC

Fault

The inverter has detected a PFC circuit over-current condition

•

Error occurs when PFC detects an over current condition of 100A peak.

• If condition is detected, outdoor unit will stop (compressor and fan) – service soon condition.

• Anti-short cycle timer is initiated.

•

If condition occurs 10 times within 60 consecutive minutes, the system will lockout – service

urgent condition.

•

Inverter LEDs will flash code 27.

• Refer to the unit service documentation for detailed troubleshooting procedures.

Inverter flash code 27.

The sequence is:
•

Red LED: Two Flashes

•

Green LED: Seven Flashes

NOTE:

Inverter normal operations with no error code present is as follows. Red LED is ON and

Green LED is OFF.

To clear, disconnect power to outdoor unit

and restart.

Summary of Contents for 100017





















































Search results

Summary of Contents for 100017

Reviews:

Related manuals for 100017

Brands by name

Popular brands

Lennox 100017, Manual

Search results

Summary of Contents for 100017

Reviews:

Related manuals for 100017

Brands by name

Popular brands