Lennox Hearth Products Traditions T300P Series Installation And Operation Manual Download | Manualshive

Page: 9 / 40

background image

INSTALLATION

Page 9

THERMOSTAT INSTALLATION:

NOTE: Always Disconnect Power Before Perform-
ing The Thermostat Installation.

A 24-volt wall thermostat and 20 feet of 18-gage ther-
mostat wire is included in your stoves accessory pack-
age. It is recommended that the thermostat and ther-
mostat wire be installed by an authorized Lennox
Hearth Products dealer.

Installation Steps:
1. Unplug stove power cord from the wall outlet.
2. Locate the thermostat terminal block (see illustra-

tion).

3. Loosen the two terminal screws on the terminal

block and remove the jumper.

4. Connect the two wires from your thermostat to the

terminals (one per terminal). Ensure that the purple
wires from the harness remain connected to the ter-
minal block and tighten the terminal screws. Make
sure the wires are firmly connected to the thermo-
stat.

5. Plug in the stove and you are ready to operate with

your thermostat!

IMPORTANT: IF THE WALL THERMOSTAT PRO-
VIDED IS NOT USED, THE JUMPER IS REQUIRED
FOR THE STOVE TO OPERATE.

Terminal Block for Thermostat

Leave Jumper on, If Thermostat Is Not Used

Remove Jumper if Thermostat Is To Be Used

Model T300P Series

(viewed from stove back)

Jumper

«
...
7
8
9
10
11
...
»

Summary of Contents for Traditions T300P Series









































Reviews:

No comments

Related manuals for Traditions T300P Series

Brand: HAAS + SOHN Pages: 36

Brand: Saey Pages: 41

HRV 140 Silhouette

Brand: Ravelli Pages: 76

Advance Pellet Stove

Brand: Harman Pages: 44

Brand: Extraflame Pages: 40

Brand: Defy Pages: 18

Ellis Cook Stove BCS01

Brand: Boru Stoves Pages: 32

Grandview GV230

Brand: Lennox Hearth Products Pages: 32

CAMP'BISTRO DLX

Brand: Campingaz Pages: 27

Brand: Campingaz Pages: 76

Brand: Chip Energy Pages: 8

Brand: Dunsley Heat Pages: 15

HSP 7 DIANA GRANDE RLU 451.08

Brand: HAAS + SOHN Pages: 23

Brand: USSC Pages: 36

SIROCCO SC30L.NZ

Brand: Blaze King Pages: 48

Brand: Legendfires Pages: 8

Brand: Wood Stone Pages: 23

MBL TERMOPALEX 78

Brand: Palazzetti Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands