Lennox Hearth Products Traditions T300P Series Installation And Operation Manual Download | Manualshive

Page: 15 / 40

background image

INSTALLATION

PAGE 15

Installation Configurations / Standard Venting Options

This appliance may be connected to an existing flue or
by installing listed type “PL” vent pipe. If a liner is run all
the way to the top of the existing chimney, the existing
flue should be sealed with a steel plate. Start a vertical
run with a Tee at the back of the stove. Other options
are illustrated below.

Note:

See page 11 for

Vent Termi-

nation

Requirements

.

Preferred Installation – Vertical Vent Through the Roof.
This venting configuration allows for the best stove
performance. The vertical pipe promotes natural draft
and with the chimney inside the dwelling, the flue
gases stay warm, thus rising at a consistent rate.

«
...
13
14
15
16
17
...
»

Summary of Contents for Traditions T300P Series









































Reviews:

No comments

Related manuals for Traditions T300P Series

Brand: Valor Pages: 7

Brand: MSR Pages: 2

G421 Studio2 White Special

Brand: gabriel Pages: 24

Infinity Plus 11

Brand: Ravelli Pages: 184

Brand: Harman Pages: 40

VOGELZANG VG1820

Brand: United States Stove Pages: 40

Ashley AW3200E-P

Brand: United States Stove Company Pages: 40

Brand: United States Stove Company Pages: 48

BEA majolica oven

Brand: Cola Pages: 12

Brand: Procom Pages: 28

Brand: Contura Pages: 20

Highlander 5 Enviro-Burn

Brand: Dunsley Heat Pages: 12

Brand: Dunsley Heat Pages: 12

YORKSHIRE 4022249

Brand: Dunsley Heat Pages: 15

Brand: De Vielle Pages: 8

Brand: Stove Builder International Pages: 6

Brand: Ventis Pages: 52

Brand: Vogelzang International Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands