background image

WASHING PROCEDURES

   Press  down  the  Power  Button , the washer 
   enters a mode of normal wash procedure.

   Select  a  proper  water   level  based  on  the
   quentity of clothes.(The washer will not start
   before water reaches the set level.)

   PROCESS SELECTION:
   If the full  cycle of wash ,  rinse  and  spin  is
   not entired,the desired process  can  be select
   (please reference to 

Functions of operating

   switches
   PROGRAM SELECTION:
   REGULAR: for cottons,linens,synthetic 
                        fabrics.
   GENTLE: for silks,knits and soft clothes.
   TUB CLEANING: use this program to clean 
   the tub regularly.

  The machine starts to  work on pressing  
    down  START/HOLD  button . As the  washer 
   finishes  washing,the buzzer buzzes and the 
  power switch  cuts  off  power  supply  
 automatically , the

   

REGULAR

light 

1. First loose the  adjust  foot  knob , place   the 
   washer evenly and stably,and tighten 
2. Connect  with the water inlet hose , and 
   on the water tap.
3. Insert  the  power plug into the power socket
   (with the earth lead properly connected).
4. Hang  the upper drain hose on the pond.
5. Loosely  put  clothes  wash into the tub ( be
   careful  not  to  leave coins 

keys etc.hard 

   arti

6. Put an  appropriate amount of  detergent into
   the tub , too much of  it is both  a  waste  and
   difficult  to  rinse . Please  refer  to  the Table
   of Amount of Detergent.

the knob.

turn

cles   in  their  pockets , in  case  they will 

   damage the tub.

   remain indicating.

1

2

3

4

5

START

HOLD

WATER LEVEL

AUTOMATIC TURNOFF

POWER

LOW

HIGH

RESET

MEDIUM

ON

OFF

>

7

5

0

m

m

Note: 
The  water  will  overflow when  the  height 
of  the drain hose under 750mm.

Summary of Contents for XQB22-(AUS)22G











Reviews: