10.4
Emergency-button interface EA-NT-IN (Art. No: 100.0250A)
Alarm-input:
4.8 to 35
V DC / limited to 10 mA / Isolation: 1.5kV => (parallel to horn
Output-switch:
Contact NC or NO: max. 350 V/0.12 A (30 Ohm) => to plug X2
10.5
Misuse-protection interface EA-2DOOR (Art. No: 100.0260A)
Door-state-signals (2x):
active 10 to 35 V DC, status LED
Dimension:
35 x 90 x 30 mm (L x W x H) / DIN-Rail 2 units
10.6
Emergency lights (Art. No: 100.087x)
10.6.1
LED-strip 10 cm(Art. No: 100.0870) self-adhesive
Suitable to transparent frames (100.0231)
Specification:
12 V DC +/- 15% / 0.8 W / 52 lm (16 cd 120°)
Dimension:
117 x 9 x 9 mm (L x W x H)
10.6.2
LED-strips 2 x 10cm (Art. No: 100.0873) self-adhesive
Like 100.0870, but 2 stripes for light upwards and downwards
Specification:
12 V DC +/- 15% / 1.6 W / 104 lm (16 cd 120°)
Dimension:
(100+117) x 9 x 9 mm (L x W x H)
10.6.3
LED-screw (Art. No: 100.0872) / IP67
Specification:
12 V DC +/- 15% / 0.2 W / 4 lm (44 cd 20°)
Mounting:
Screw M8
Cable: 25 cm
10.6.4
LED-Ring (Art. No: 100.0879)
Specification:
4 to 15 V DC / 1 W
Dimension:
52 x 52 x 6 mm (L x W x H)
Suitable to polycarbonate front panels (Art. No: 100.0211 / 0212 / 0213) in Rx42-gap
10.7
Telephone line interfaces
10.7.1
Alarm forwarding over mobile network / Gateway
Simulates the analogue telephone line for EasyAlarm® and is compatible with the protocols WinMOS ® 300 and Point ID.
Notes:
The antenna should be mounted in a fixed location (e.g. in the engine room), to ensure a stable reception situation.
In the case of an retrofit (SNEL, ESBA), where no telephone wires in the hanging cables are available, the gateway
can be mounted on top of the cabin, if the reception is ensured throughout the entire travel the elevator.
If the coverage is inadequate or fails completely, the system must be placed out of service automatically, for example
with a command “move to ground floor” send to the elevator control. For this purpose, the gateway includes a potential
free relay contact (NO or NC).
Beware of prepaid SIM: Where appropriate in the case of alarm, no funds are available. A postpaid or a prepaid with
automatic reloading is preferable.
Connectors:
1 x Line (for i.e. alarm units EasyAlarm® / Exicall EN70 / MINI
1 x permanent 12V-output for alarm units and horn
1 x switched 12V-output for emergency light
1 x Relay-contact
Operation monitoring “System ready“
1 x SMA-antenna jack (patch sticking antenna included)
Status:
reception level with LED
Backup:
12 V battery (e.g. Art. No: 100.0880)
Approval:
TÜV AUSTRIA, Report number: AT – 08 / 0028
10.7.1.1 EA-UMTS-IP (Art. No: 100.0802BU) / EA-UMTS-IP-LIGHT (Art. No: 100.0801BU)
Supply voltage:
230 V AC / 50 Hz
Dimension:
182 x 180 x 63 mm (L x W x H) / protective housing IP65
10.7.1.2 EA-UMTS-DIN (Art. No: 100.0812BU) / EA-UMTS-DIN-LIGHT (Art. No: 100.0811BU)
Supply voltage:
Art. No: 1
AC
.0812B:
230 V AC / 50 Hz (incl. Art. No: 118.0117)
Art. No: 1
DC
.0812B:
9 – 35 V DC
(incl. Art. No: 118.0119)
Dimension:
45 x 118 x 135 mm (L x W x H) / DIN-Rail
add 17.5 x 93 x 68.5 mm for DIN-adapter
10.7.1.3 RDT Remote-Data-Transmission modules for 100.802B or 100.0812B
Data-Module:
Art. No: 100.0850:
DB9 for compatible elevator controls
Art. No: 100.0851:
Mini-USB for compatible elevator controls
Dimension:
35 x 90 x 30 mm (L x W x H) / DIN-Rail 2 units
10.7.2
DECT-Interface
DECT-Interface for wireless connection between cabin and machine room , when there is
no hanging cable available for telephone line.
31
