Leister ALLIED VARIMAT V2 Manual Download Page 3

19

Leister  VARIMAT V2

Automatic hot-air welding machine

Application

•   Overlap welding of roofing membranes made of PVC, TPO, ECB, EPDM, CSPE for basic weld seams. 

 

Can also be used in areas close to edges and on uneven surfaces.

• Overlap welding of sheets and coated fabrics

Please read operating instructions carefully before use 

and keep for future reference.

Incorrect use of the hot air tool can present a 

fire and explosion hazard

 

especially near combustable materials and explosive gases.

Do not touch

 hot welding nozzle and welding plate as they can cause 

burns

Allow the tool to cool down. Do not point the hot-air flow in direction of people 

or animals.

Danger to life 

when opening the device as live components and connections are  

exposed. Unplug the line/mains plug from the plug socket before opening the device. 

Warning

Connect tool to a 

receptacle with protective earth terminal

. Any interruption of 

the protective earth conductor inside or outside the tool is dangerous!

Use only extension cables/cords with protective earth conductor ! 

For personal protection, we strongly recommend the tool be connected to an 

RCCB

 (

R

esidual 

C

urrent 

C

ircuit 

B

reaker) before using it on construction sites.

FI

Protect the device 

from damp and wet.

The tool must be operated 

under supervision.

 

Heat can ignite flammable materials which are not in view.
The device machine may only be used by 

qualified specialists

 or under their super-

vision. Children are not authorized to use this device.

Rated voltage

 stated on the device must correspond to line/mains voltage. 

N 61000-3-11; Z

max 

= 0.115 

Ω

 + j 0.072 

Ω

. If necessary, consultate supply 

authority. 

Extract hot-air blower in case of

 power breakdown

.

230

400

Caution

Device must not be lifted at additional weight / end weight.

Operating Instructions 

(Translation of the original operating instructions)

GB

USA

Summary of Contents for ALLIED VARIMAT V2


















Reviews: