background image

6

Instructions for Use V 3.4 RevI – 09/2018

1.2  Qualification of personnel

•  The Leica HI1210 may be operated by trained 

laboratory personnel only.

•  All laboratory personnel designated to operate 

this instrument must read these Instructions 

for Use carefully and must be familiar with all 

technical features of the instrument before 

attempting to operate it.

1.3  Intended use of instrument

The Leica HI1210 is a paraffin flotation bath 

for flattening and drying cut tissue samples 

used in all fields of biomedical research and 

routine diagnostics. It may only be used by 

Leica  Biosystems Nussloch GmbH for operating 

 approved instrument accessories.

1.4  Instrument type

All information provided in these Instructions for 

Use applies only to the instrument type indicated 

on the cover page. 
A nameplate indicating the instrument serial 

number is attached to the rear side of the instru-

ment.

Any use of the instrument other than 

its designated use is considered im-

proper.

Failure to adhere to these instructions 

may result in an accident, personal 

injury, damage to the instrument or 

 accessory  equipment.

Proper and intended use includes 

compliance with all inspection and 

maintenance instructions, along with 

the observance of all instructions in 

the Instructions for Use.

1. 

Important Information

The Regulatory Compliance Mark 

(RCM) indicates a device’s compliance 

with applicable ACMA technical stan-

dards of New Zealand and Australia 

- that is, for telecommunications, radio 

communications, EMC and EME.

Summary of Contents for HI1210



















Reviews: