Lehner Lifttechnik OMEGA-F Installation Manual Download Page 2

Page: 2 / 53

OMEGA

Installation Manual

Edition February

2020

Omega

platform lift

page 2 of 52

CONTENTS

OBSERVE THE FOLLOWING POINTS BEFORE INSTALLATION! .................................... 4

STEP 1. – INSTALLATION OF THE GUIDE RAILS .............................................................. 5

STEP 2. INSTALLATION OF THE DRIVE BOX .................................................................... 7

STEP 3. INSTALLATION OF THE TENSION AND SUPPORT ROPE SYSTEM .................. 7

Installing the tension rope ................................................................................................................... 9

Installing the support rope ................................................................................................................ 12

STEP 4. INSTALLATION OF THE PLATFORM ONTO THE RAIL/ROPE SYSTEM .......... 16

STEP 5. TIGHTENING AND CONNECTION THE ROPES ................................................. 17

STEP 6: ELECTRICAL CONNECTIONS ............................................................................. 17

STEP 7. MOUNTING THE MECHANICAL STOP STATION ASSEMBLY .......................... 19

STEP 8: ADJUSTMENT OF THE LOADING RAMPS ......................................................... 21

STEP 9: PROGRAMMING THE UNIT ................................................................................. 22

Programming the drive speeds - Teach-in mode ............................................................................. 28

ERROR LIST AND EXPLANATION .................................................................................... 31

FINAL CHECKS ................................................................................................................... 37

EMERGENCY OPERATION ................................................................................................ 38

EXPLANATION OF THE ELECTRICAL CONCEPT ........................................................... 39

DRIVE UNIT ......................................................................................................................... 40

Drive unit control board .................................................................................................................... 40

Buttons and Jumpers ......................................................................................................................... 43

Main contactor control board (MCCB) ........................................................................................... 44

Summary of Contents for OMEGA-F






















































Search results

Summary of Contents for OMEGA-F

Reviews:

Related manuals for OMEGA-F

Brands by name

Popular brands

Lehner Lifttechnik OMEGA-F, Installation Manual

Search results

Summary of Contents for OMEGA-F

Reviews:

Related manuals for OMEGA-F

Brands by name

Popular brands