LEGRAND Radiant Series Installation Manual Download Page 63

Page: 63 / 208

before you start

Review this guide in its entirety before beginning device installation. Consult an

electrician with any questions or if you are unsure of your abilities.

Warning:

Incorrect installation could

result in death, serious injury, and/or

damage to your home or devices.

Caution:

To reduce the risk of injury

and/or overheating and damage to other

equipment:
•  For dry, indoor use only.
•  Use ONLY with dimmable lighting loads.
•  Do not use to power medical equipment.

• Do not use with loads exceeding the

device load rating (see page 22).

• Connect the smart dimmer to a

120 VAC, 60 Hz power source ONLY.

• Always use copper wire to install the

smart dimmer and follow all applicable

local and national electrical codes.

• Install in a non-metallic electrical box

to protect wireless signal strength.

Visit the Legrand website at

www.legrand.us/radiant/smart-lighting.aspx

to learn more

about your smart device.

Summary of Contents for Radiant Series









































































































































































































Search results

Summary of Contents for Radiant Series

Reviews:

Brands by name

Popular brands

LEGRAND Radiant Series, Installation Manual

Search results

Summary of Contents for Radiant Series

Reviews:

Brands by name

Popular brands