LEGRAND Radiant Series Installation Manual Download Page 112

Page: 112 / 208

getting to know your remote dimmer

Item Name

Description

Paddle

Switch

• Press the top of the paddle to turn the light on or double-tap to

raise the dimming percentage to 100%.

• Press the bottom of the paddle to turn the light off.

• To return the dimmer to factory default, press and hold the top of

the paddle for 15 seconds. The LED illuminates a solid amber

color. To complete the factory reset, you must also remove the

device from your Samsung Artik Cloud account before it can be

recommissioned with your existing Hub or a new Hub.

LED Locator

Light

Indicates the current state of the device. Refer to “LED

Locator Light Explanations” for detail.

Dimmer

Paddle and

LED Light

Level

Controls and displays the dimming percentage:

• Press (+/-) to adjust the dimming level incrementally.

• Press and hold (+/-) to quickly change the dimming level.

Summary of Contents for Radiant Series









































































































































































































Search results

Summary of Contents for Radiant Series

Reviews:

Brands by name

Popular brands

LEGRAND Radiant Series, Installation Manual

Search results

Summary of Contents for Radiant Series

Reviews:

Brands by name

Popular brands