LEGRAND Radiant Series Installation Manual Download Page 24

Page: 24 / 208

regulatory information

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

Summary of Contents for Radiant Series









































































































































































































Search results

Summary of Contents for Radiant Series

Reviews:

Brands by name

Popular brands

LEGRAND Radiant Series, Installation Manual

Search results

Summary of Contents for Radiant Series

Reviews:

Brands by name

Popular brands