background image

26

1 Introduction

®

The Keor LP is an Uninterruptible Power Supply (UPS) designed for home, commercial and 

industrial application. This manual contains information for users of the Keor LP 1,2,3 kVA models.

You are advised to read carefully this handbook and the safety instruction sheet included in 

the packaging before installing your uninterruptible power supply, meticulously following 

the instructions given herein. In case of problems with the UPS, please read this manual before 

contacting the technical support; 

Please download the latest version of the manual from the website: www.ups.legrand.com

•   The UPS has been designed to supply data processing equipment; The load applied must not 

exceed the one indicated on the rear label of your UPS.

  Ensure that the input voltage of the UPS matches the utility supply voltage. Use a certified input 

power cable with the correct plugs and sockets for the system voltage.

•   The ON/OFF button of your UPS does not electrically isolate the internal parts. To isolate your 

UPS unplug it from the mains power socket.

•   Do not open the UPS container since there may be parts inside with dangerously high voltage 

even when the mains plug is disconnected; there are no parts inside that the user can repair.

•   The front control panel is provided for manual operations; Do not press on the panel with sharp 

or pointed objects.

•  The UPS Keor LP has been designed to work in closed, clean rooms where there are no 

inflammable liquids or corrosive substances and where it is not too damp.

•  Do not place near equipments that generate strong electro-magnetic fields and/or near 

equipments that are sensible to electro-magnetic fields. (engines, floppy disks, speakers, 

adapters, monitors, video, etc...)

•   Do not pour any liquid on the UPS or inside the UPS.
•   Do not place the UPS in humid environment or near liquid, such as water, chemical solution…
•   Do not expose the UPS to the direct sunlight or any heat sources. 

  Ensure that the installation site is free from excessive dust and the ambient temperature and 

humidity are within the specified limits.

2 Condition of use

40

0%~90%

200mm/

8 inch

200mm/

8 inch

200mm/

8 inch

Summary of Contents for KEOR LP























Reviews: