manualshive.com logo in svg

LEGRAND 0 625 14, Manual

Share
Download
LEGRAND 0 625 14 Manual Download Page 9

9/11

Technical data sheet: S000082102EN-1 

Updated: 08/10/2013 

Created: 08/10/2013

Cat. No(s): 0 625 14/24/54/64/74

Kickspot Self-testing/AutoDiag

self-contained emergency lighting unit 

4. USE (CONTINUED)

5. MAINTENANCE

n

 5.1 Routine maintenance

• Safety Regulations for Public Buildings (articles EL 18 and EC 13)

Routine  maintenance  of  self-contained  emergency  lighting  units  is 

mandatory in public buildings.

It  can  be  carried  out  in  accordance  with  the  provisions  of  standard 

NF C 71-830.

The user must ensure that the lighting units are regularly checked and 

serviced.

The  user  must  ensure  that  the  annual  maintenance  operations  are 

carried out by a qualified person.

After  every  annual  maintenance  operation,  the  qualified  person  must 

affix a new maintenance label and fill it in.

This  maintenance  label  (Cat.  No.  0  609  01)  must  be  affixed  to  each 

lighting  unit  in  a  position  where  it  can  be  seen,  and  marked  with  the 

date on which the unit is returned to service.

• Operation (article EC 14)

The emergency lighting must be set to standby state during operating 

periods.

The emergency lighting must be set to rest or off state when the normal 

lighting installation is switched off intentionally.

The use of a hard-wired remote control Cat No. 0 039 00 and keyswitch 

in accordance with wiring diagram 3.2 enables the units to be set to rest 

state at the same time as the normal lighting is switched off when the 

rooms or areas are not in use.

The user must regularly check the following:

Once a month:

- That the unit switches to operating position if the normal power supply 

fails, and that all the lights come on (operation must be strictly limited 

to the time required to carry out the visual check). These checks can be 

carried out by checking that the green self-test indicator is on on all the 

units in the installation.

- The effectiveness of the remote command to switch to rest position and 

the automatic return to standby position when the normal power supply 

is re-established.

Once every six months:

- At least one hour's standby power. These checks can be carried out by 

checking that the green self-test indicator is on on all the units in the 

installation.

n

 4.9 Operation of self-contained emergency li reinforced 

emergency light Cat. No. 0 625 54 with a remote control module Cat. 

No. 0 039 00 connected to a fire alarm control panel

Mains power 

supply

Fire alarm

Unit status

Emergency function

Present

Absent

Standby

Present

Present

Backup with flux 

dimming between 

 

45 lumens and  

120 lumens

Absent

Present or 

absent

Backup with flux 

dimming between 

 

45 lumens and  

120 lumens

Lighting unit

standby and

emergency

LEDs

Unit green

status LED

Yellow

fault LED

Summary of Contents for 0 625 14












Reviews:

No comments

Brands by name

Popular brands

Load more brands