LEGRAND 0 489 55 Manual Download Page 9

9/9

Technical data sheet: S000105459EN-2 

Updated: 25/02/2021 

Created: 05/12/2018

Microwave detector - DALI/DSI dimming

Cat. No(s): 0 489 55/56/57

CONTENTS

  9. PERFORMANCE

Detection area

For the classroom

For corridors and aisles

For open-plan offices

CAUTION:  Always test before using other special cleaning 

products.

  10. CARE

Keep the lens clean, use a cloth to clean the surface.

Do not use acetone, tar-removing cleaning agents or trichloroethylene.

  11. STANDARDS

Directive: CE
Installation standards: NFC 15-100
Product standards: NF EN 60730-1
Environmental standards:
− 

European Directive 2012/19/EU: WEEE (Waste Electrical and 

Electronic Equipment)
− 

European Directive 2011/65/EU and 2015/863: RoHS 

(Restriction of Hazardous Substances)
− 

Decrees and/or regulations: Public buildings, workplace 

buildings, high-rise buildings
− 

RED Directive: 2014/53/EU)

Sensitivity set to 80% 

Detector head position set to 40°

2.6 m

6 m

19 m

Sensitivity set to maximum 

Detector head position set to 80°

2.6 m

6 m

23 m

High 

sensitivity area

Low 

sensitivity area

High 

sensitivity area

Low 

sensitivity area

High 

sensitivity area

Low 

sensitivity area

2.6 m

6 m

17 m

Sensitivity set to maximum 

Detector head position set to 0°

Summary of Contents for 0 489 55










Reviews: