Leggett & Platt Vertex Fasteners Prostick VA0318 Operating Manual Download Page 9 | Manualshive

Page: 9 / 13

background image

8

Rev. A

To Reassemble Magazine

1. Insert pin VH0538 into magazine VC4136 and thru eyelet of springs VC4132.

2. Pull springs around pulleys in magazine and attach each eyelet to pusher

VC4135. Place pusher into track of magazine.

3. Insert pin VC4133 and spring VH0537 into pocket in magazine.

«
...
7
8
9
10
11
...
»

Summary of Contents for Vertex Fasteners Prostick VA0318














Reviews:

No comments

Related manuals for Vertex Fasteners Prostick VA0318

Brand: Gearwrench Pages: 3

DC POWER-L Series

Brand: Salicru Pages: 32

Brand: Xantrex Pages: 3

Brand: Parkside Pages: 76

Brand: Fein Pages: 61

Brand: Eastwood Pages: 8

Brand: Eastwood Pages: 8

Brand: SOMMER Pages: 20

Brand: IGM Professional Pages: 56

Brand: Band-it Pages: 4

Brand: Chicago Pneumatic Pages: 196

Brand: X-Tronic Pages: 8

Brand: Rapid Pages: 87

Brand: Matatakitoyo Torque Tools Pages: 2

Brand: Kitagawa Pages: 69

SmartOnline 5KVA

Brand: Tripp Lite Pages: 28

Brand: Daiwa Pages: 5

Brand: Brunton Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands