manualshive.com logo in svg

Leedarson 7AA-SS-VE-C0, Quick Start Manual

Share
Download
Leedarson 7AA-SS-VE-C0 Quick Start Manual Download Page 7

 

Caution:   
This device complies with Part 15 of the FCC rules. Operation is subject to the 
following two conditions: (1) this device may not cause harmful interference, and (2) 
this device must accept any interference received, including interference that may 
cause undesired operation.   
Changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate the equipment.   
 

Hereby,  Corporation  declares  that  this  device  is  in  compliance  with  the  essential 
requirements and other relevant provisions of Directive 2014/53/EU 
 

Special Rule Of Each Command Class 

Z-Wave Plus Info Report Command Class

Parameter 

Value 

Z-Wave Plus Version 

0x02 

Role Type 

0x06 (ZWAVEPLUS_INFO_REPORT_ROLE_TYPE_SLAVE_SLEEPING_REPOR TING) 

Node Type 

0x00 (ZWAVEPLUS_INFO_REPORT_NODE_TYPE_ZWAVEPLUS_NODE) 

Installer Icon Type 

0x0C06    (ICON_TYPE_SPECIFIC_SENSOR_NOTIFICATION_ACCESS_CONTROL) 

User Icon Type 

0x0C06    (ICON_TYPE_SPECIFIC_SENSOR_NOTIFICATION_ACCESS_CONTROL) 

Summary of Contents for 7AA-SS-VE-C0













Reviews:

No comments

Brands by name

Popular brands

Load more brands