LeeBoy 8616B Operation, Service And Parts Manual Download Page 92 | Manualshive

Page: 92 / 287

LeeBoy 8616B Operation, Service And Parts Manual Download Page 92

5

LeeBoy 8616B Conveyor Paver

5-19

Change Fuel Filter

DO NOT change the fuel filter while

the engine is running.

DO NOT smoke or change fuel

filter near open flames as diesel fuel is highly

combustible. Be careful not to spill fuel.

Fuel Filter

Figure 5-19. Fuel Filter

Replace the fuel filter using the following general
procedure.
1.  Stop the engine and allow it to cool.
2.  Put a container under the filter before removing it.
3.  Wipe the area around the fuel filter and mounting

head using a clean, lint-free cloth.

4. Use a filter removal wrench to loosen and remove

the filter by turning it clockwise.

(Figure 5-19)

5. Drain and discard the removed filter in compliance

with local and federal environmental laws..

6. Wipe inside the filter head with a clean, lint-free

cloth.

7.  Fill the new fuel filter element with the diesel fuel.
8.  Wipe a little fuel on the rubber gasket.
9.  Install the new fuel filter element onto the filter head,

carefully tightening the element by hand.

Tighten the fuel filter as directed on by

the filter manufacturer. DO NOT overtighten the fuel
filter element onto the filter head.

10. Start the engine and check for any fuel leaks.

Explosion Hazard! Stop the engine

immediately if any fuel leakage is noted. DO NOT
start the engine until the leak has been corrected.

HYDRAULIC SYSTEM

Check Hydraulic Oil

The hydraulic motors and hydraulic cylinders use the
same hydraulic oil reservoir and hydraulic oil supply.

Take care when working with the

hydraulic system to ensure it is completely clean.

Never allow the hydraulic oil level to

fall too low. Pump damage will occur.

Check the hydraulic reservoir oil level daily using the
sight gauge on the left side of the paver.

(Figure 5-20)

Check the hydraulic oil level when the hydraulic oil is at
normal operating temperature for an accurate reading.
If the hydraulic oil level falls below the black line, add
more hydraulic oil.

Hydraulic Oil

Level Line

Figure 5-20. Hydraulic Oil Sight Gauge

DO NOT loosen or remove the

hydraulic oil strainer fill cap when the hydraulic oil

is hot. Always loosen the cap slowly to relieve any
pressure in the hydraulic oil reservoir.

«
...
90
91
92
93
94
...
»

Summary of Contents for 8616B
































































































































































































































































































Reviews:

No comments