background image

www.prolight.co.uk

Artisan 2000 Dual White Fresnel

  

User Manual

12

Wireless operation:

To operate the fixture wirelessly you will need to plug in the Artisan Series W-DMX Compatible  
Transceiver (sold separately) into the USB port on the rear of the fixture. W-DMX should also be set  
to 

“ON” 

in the fixtures settings (full instructions can be found on page 9). 

If using it in wireless DMX mode a compatible wireless DMX Transmitter (e.g. Wireless Solutions Sweden 
W-DMX Micro F-1 Lite G5 Transceiver) will need to be connected.
The Artisan Series W-DMX Compatible Transceiver features 2 operating protocols as listed below.  
The LED on the side of the dongle will illuminate a different colour for each operating protocol.
W-DMX G3 Transmit Protocol - Blue (when transmitting)
W-DMX Receive Protocol - Green (when receiving)
To set the dongle in one of these modes plug the  
Artisan Series W-DMX Compatible Transceiver into  
the USB port on the rear of the fixture. Hold down  
the button on the dongle whilst powering on the unit.  
The LED will illuminate white for a brief moment and  
then change colour. You can then press the button which  
will scroll through the operating protocols. Once you have selected the chosen protocol, press and hold 
the button on the dongle for 3 seconds. The LED will illuminate white, then turn blue (transmit mode) or 
stay white (receive mode). The unit is now set in your chosen protocol.

W-DMX G3 Transmit Protocol:

Once in this protocol the LED will illuminate blue. This indicates the fixture is ready to pair with the 
receiver(s). Once all the receiver(s) have been set up press the button on the dongle once and the LED 
will flash blue quickly, this indicates it is attempting to pair with the receivers. Once pairing is complete 
the LED will illuminate static blue to indicate the fixture is transmitting signal.
To disconnect the transmitting fixture from all receiving fixtures within range when connected, hold the 
button on the transmitting fixtures dongle down for 3 seconds until the LED illuminates red.  
This indicates the wireless memory has been cleared.  

W-DMX Receive Protocol:

Once in this protocol the LED will illuminate white. This indicates a connection has not yet been  
established with the transmitter. Once the transmitter has been set up press the button on the  
transmitter fixtures dongle once or press the pair button on your wireless transceiver. The LED on the 
receiving units will flash green quickly, this indicates it is attempting to pair with the transmitter.  
Once pairing is complete the LED will illuminate static green to indicate the fixture is receiving signal.
To disconnect the transmitting fixture from all receiving fixtures within range when connected, hold the 
button on the transmitting fixtures dongle down for 3 seconds until the LED illuminates white.  
This indicates the wireless memory has been cleared.  
If the indicator on the receiving units flashes red quickly this indicates that the signal from the  
transmitting fixture has been lost.

Operating instructions

Summary of Contents for Artisan 2000 Dual White Fresnel



















Reviews: