background image

4/4

 CONNECT WITH RGB STRIP CONNECTOR CORD 

Another option for quick, easy and exible connection between RGB 
LED strips is our RGB Strip Connector Cord. RGB Strip Connector 
Cord are useful option in application where you want to easily joint 
light strips over separated surfaces, such as between kitchen cabinet.

Apply 1 ½” long electrical heat shrink over all connection points. Secure connection wire with wire 
clamp. 

Note: Diagram below shows 2 wire, but RGB strip will have 4 wires

 

IMPORTANT ! 

Wrong!

4"

(100mm)

On widest one flat plane (only)

Do not bend sideways. 

Flexible on one axis

maximum band radius 4”

R

G

B

R

G

B

R

G

B

R

G

B

RGB Connector Cord

TROUBLESHOOTING 

Tape light strip does not light

Ÿ

Make sure your power supply is turned on and has the correct voltage.

Ÿ

Conrm you have the correct polarity (+ to + and - and -) throughout the run of LED Lighting.

Ÿ

Have a electrician check all connections and any switch or dimmer connections from the power supply to the LED Light Strips.

Ÿ

Consider testing with a multimeter to ensure light strip is receiving 12V power. 

LED Flex Strip lights blink on, then go off

Ÿ

The power supply is not adequate for the length of LED Light Strips you are powering. Install a adequate Class 2 power supply.

LEDs farthest from the power supply are noticeably dimmer

Ÿ

This is the result of voltage drop. Decrease the length of the 12V power feed or use thicker power feed wires between the 12V power 
supply and the lighting strips.

G

IMPORTANT NOTE

Polarity marks must match

otherwise strip will not work

R

G

B

G

+

R B

G

+

R B

G

IMPORTANT INSTRUCTIONS

MAXIMUM FLEXSTRIP LENGTH SUPPORTED BY LED WORLD’s CLASS 2 POWER SUPPLY

Power Supply

Max Feet of LED Flexstrips

Power Supply

Max Feet of LED Flexstrips

XLD75B-112V-FC

27.2 Feet (Continuous 60 Watts)

XLD200B-412V-FC

4 X 18 Feet (Each Channel)
Total 72 Feet

YHY-12005000

22 Feet (Continuous 48 Watts)

CVN50L12DC

18.18 Feet (Continuous 40 Watts)

RGB LED FLEX STRIP

  

Model

: FA30M50-5M-12V-RGB (RGB: Red, Green, Blue)

 

1-800-387-4081

 

ledworldlighting.com ledworld.ca

 | 

 

Copyright © 2019 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).

LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 4.0 - 09/18/19

Summary of Contents for FA30M50-5M-12V-RGB

Page 1: ...n perform installation familiar with low voltage wiring techniques Correct polarity is imperative is marked on printed circuit Parallel connection only Ÿ DO NOT install on ammable material or possibility of in the future Do not install any luminaire closer than 6 inches 15 25 cm from any curtain or similar combustible materials Ÿ The light and all its components cannot be mechanically pressed Neve...

Page 2: ...starting the installation process General questions based on lighting requirements Ÿ Where will your power supply be located Ÿ How will you switch your LED lighting ON and OFF Ÿ What is the best layout con guration for your installation with wiring consideration Ÿ How will you run your wiring to your LED strip lighting WATTAGE CALCULATION The LED Flex Strips have a label on each roll that indicate...

Page 3: ...ilable 48W 12W LAYOUT OPTIONS Note Always check the Wattage of your LED Strip or Fixture Power Supply Wattage x 0 8 Available Wattage Class 2 Power Supply 60W Class 2 Power Supply 60W Layout 1 22W 22W 30W 30W Available 48W Available 48W Layout with Overload Do Not Use Securely mount wires using wire clamps AC120V 40W 40W 40W 50W 50W 50W 50W Note Peel 3M tape before using with Quick Connectors RGB ...

Page 4: ... Strip lights blink on then go off Ÿ The power supply is not adequate for the length of LED Light Strips you are powering Install a adequate Class 2 power supply LEDs farthest from the power supply are noticeably dimmer Ÿ This is the result of voltage drop Decrease the length of the 12V power feed or use thicker power feed wires between the 12V power supply and the lighting strips G IMPORTANT NOTE...

Reviews: