background image

Introduction

Safety

Failure to follow all instructions listed in this manual may result in equipment failure or serious injury.

If using trim tabs for the first time, follow the Operation section of this manual to familiarize yourself with the 

feel and response of your trim tab system.

Never deploy tabs in a following sea. Keep tabs fully retracted in a following sea.

Never deploy tabs quickly at high speeds or above cruising speeds. This may cause the boat to turn quickly 

and become unstable and difficult to control.

Stay alert, watch what you are doing and use common sense when operating your trim tab system.

Do not use the trim tab system when under the influence of drugs, alcohol or medication. A moment of 

inattention while operating the trim tab system my result in serious injury.

Lectrotab introduces an automatic leveling control system to maintain the boat on a level plane and ensure a 
comfortable ride. If sea conditions change, adjustments in boat speed occur, or passengers move about the 
boat, the automatic leveling control system utilizes built in sensors to correct the attitude of the boat to 
maintain the proper level. The control incorporates advanced programming to correctly level boats 20 foot 
or larger.

The Lectrotab automatic leveling control (ALC) design advantages and features include:

• Improved fuel 

efficiency and faster speeds

• 

Internal GPS (does not require connection to GPS antenna)

• 

Actuators connect directly to display (ALC-1 for single actuator system does not require a control box)

• Faster planing at slower speeds

• 

Automatic correction of bow high conditions or listing 

• 

Automatic tab retraction once ignition key or accessory switch switched off

• 

Automatic corrections while turning are ignored

• Completely sealed and waterproof 

display

• 

Automatic dimming of display LED indicators in darkness and brighten in sun light

• 

Operates on 10 to 30 Volts DC

• 

2 Year Warranty

• 

CE Approved (Compliance with EMC regulations)

3

Summary of Contents for ALC-1D












Reviews: