Lectrosonics Octopack Instruction Manual Download Page 20

15 August 2011

581 Laser Road NE   •  Rio Rancho, NM  87124  USA  •  www.lectrosonics.com
(505) 892-4501  •  (800) 821-1121  •  fax (505) 892-6243  •  [email protected]

LIMITED ONE YEAR WARRANTY

The equipment is warranted for one year from date of purchase against defects in 

materials or workmanship provided it was purchased from an authorized dealer. This 
warranty does not cover equipment which has been abused or damaged by careless 
handling or shipping. This warranty does not apply to used or demonstrator equipment.

Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any 
defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot 
correct the defect in your equipment, it will be replaced at no charge with a similar new 

item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you.

This warranty applies only to items returned to Lectrosonics, Inc. or an authorized 

dealer, shipping costs prepaid, within one year from the date of purchase.

This Limited Warranty is governed by the laws of the State of New Mexico. It states the 
entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any 
breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR 

ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT 
SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, 

OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE 
THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE 
POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF 
LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE 
EQUIPMENT.

This warranty gives you specific legal rights. You may have additional legal rights which 
vary from state to state.

Summary of Contents for Octopack





















Reviews: