manualshive.com logo in svg

Lectrosonics Octopack, Instruction Manual

Share
Download
Lectrosonics Octopack Instruction Manual Download Page 13

Receiver Multicoupler

Rio Rancho, NM

13

Coaxial Cables

A variety of low loss coaxial cables are available to 

avoid signal loss through longer runs between antenna 

and receiver. Lengths include 2, 15, 25, 50 and 100 

foot lengths. The longer cables are constructed of 

Belden 9913F with special connectors that terminate 

directly to BNC jacks, eliminating the need for adapters 

that can introduce additional signal loss.

Customized RF Distribution and Routing

Customized antenna and RF distribution is easy to 

configure using the UFM230 amplifier, BIAST power 

inserter, several RF splitter/combiners and passive 

filters. These professional grade components preserve 

signal quality and suppress noise and intermodulation. 

Optional Accessories

UFM230 Filter/Amp

Bias-T Power Inserter

8-Way Splitter/Combiner

4-way Splitter/Combiner

2-way Splitter/Combiner

PF50 Inline Filter

PF25 Inline Filter

ARG Series Coaxial Cables

Summary of Contents for Octopack





















Reviews:

No comments

Brands by name

Popular brands

Load more brands