background image

HHa

LECTROSONICS, INC.

18

Service and Repair

If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equip-

ment needs repair.  Make sure you have followed the setup procedure and operating instructions.  Check the inter-

connecting cables and then go through the 

Troubleshooting 

section in this manual.

We strongly recommend that you 

do not

 try to repair the equipment yourself and 

do not

 have the local repair shop 

attempt anything other than the simplest repair.  If the repair is more complicated than a broken wire or loose con-

nection, send the unit to the factory for repair and service.  Don’t attempt to adjust any controls inside the units.  

Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require read-

justment.  

There are no adjustments inside that will make a malfunctioning unit start working

.

LECTROSONICS’ Service Department is equipped and staffed to quickly repair your equipment.  In-warranty repairs 

are made at no charge in accordance with the terms of the warranty.  Out-of-warranty repairs are charged at a mod-

est flat rate plus parts and shipping.  Since it takes almost as much time and effort to determine what is wrong as it 

does to make the repair, there is a charge for an exact quotation.  We will be happy to quote approximate charges by 

phone for out-of-warranty repairs.

Returning Units for Repair

For timely service, please follow the steps below:

A.

  DO NOT return equipment to the factory for repair without first contacting us by letter or by phone.  We need to 

know the nature of the problem, the model number and the serial number of the equipment.  We also need a 

phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time).

B.

  After receiving your request, we will issue you a return authorization number (R.A.).  This number will help 

speed your repair through our receiving and repair departments.  The return authorization number must be 

clearly shown on the 

outside

 of the shipping container.

C.

  Pack the equipment carefully and ship to us, shipping costs prepaid.  If necessary, we can provide you with the 

proper packing materials.  UPS is usually the best way to ship the units.  Heavy units should be “double-boxed” 

for safe transport.

D.

  We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or 

damage to equipment that you ship.  Of course,  we insure the equipment when we ship it back to you.

Mailing address: 

 

Shipping address: 

 

Telephone:

 

Lectrosonics, Inc. 

 

Lectrosonics, Inc. 

 

(505) 892-4501 

PO Box 15900 

 

581 Laser Rd.   

 

(800) 821-1121 Toll-free 

Rio Rancho, NM 87174 

Rio Rancho, NM  87124  

(505) 892-6243 Fax 

USA 

   USA

 

   

Web: 

   E-mail:

 

www.lectrosonics.com  

[email protected]

Lectrosonics Canada:
Mailing 

Address: 

 Telephone: 

  E-mail:

 

720 Spadina Avenue,   

(416) 596-2202  

 

Sales:    [email protected] 

 

Suite 600 

 

 

(877) 753-2876 Toll-free  

Service:  [email protected] 

Toronto, Ontario M5S 2T9 

(877-7LECTRO) 

 

   (416) 

596-6648 

Fax 

 

Summary of Contents for HHa





















Reviews: