Lectrosonics HH Alignment Procedure Download Page 4

Page: 4 / 27

and UP simultaneously will step the frequency up in increments of 16 only pressing the UP or DOWN buttons will
only increment by 1)

channel=XX

set channel (0(00) to 1020 (ff) in normal
tuning mode, 80 is 512)

Adjust radio board C1 for 2.5 VDC at radio board TP1 (VCO_CONT)

+2.45 to +2.55 VDC (+2.5)

No DC power in at battery contacts

Wait until transmitter completely powers down (approx. 4 sec)

Apply +3.0VDC, 500mA current limit in at battery contact J8 (J9 is circuit common)

Hold Power button for 3 seconds (make sure unit come on).

Measure carrier signal power to be sure the VCO starts on power up at selected
carrier frequency

≥

+10 dBm

Using the test key pad navigate to the "Freq." screen

Press MENU/SEL and UP button simultaneously to change frequency to lowest frequency. (pressing MUNU/SEL
and UP simultaneously will step the frequency up in increments of 16 only pressing the UP or DOWN buttons will
only increment by 1)

channel=XX

set channel (0(00) to 1020 (ff) in normal

tuning mode, 80 is 512)

Measure DC voltage at radio board TP1 (VCO_CONT)

+0.6 to +1.2 VDC

No DC power in at battery contacts

Wait until transmitter completely powers down (approx. 4 sec)

Apply +3.0VDC, 500mA current limit in at battery contact J8 (J9 is circuit common)

Hold Power button for 3 seconds (make sure unit come on).

Measure carrier signal power to be sure the VCO starts on power up at selected
carrier frequency

≥

+10 dBm

Carrier signal power adjustments & spectral purity measurements

Prerequisite(s): FPGA IC programmed

Momentarily connect audio board TP22 to J5 pin 4 (enter Set-up mode)

Note

Entering Set-up mode is not necessary if the Alternate Method is exercised.

Summary of Contents for HH




























Search results

Summary of Contents for HH

Reviews:

Related manuals for HH

Brands by name

Popular brands

Lectrosonics HH, Alignment Procedure

Search results

Summary of Contents for HH

Reviews:

Related manuals for HH

Brands by name

Popular brands