Lectrosonics HH Alignment Procedure Download Page 7

Page: 7 / 27

Momentarily connect audio board TP22 to J5 pin 4 (enter Set-up mode)

Note

Entering Set-up mode is not necessary if the Alternate Method is exercised.

pilotbp=1

Using the test key pad navigate to the "DevOff" screen (Mid carrier freq is highlighted)

tone=1 (sets DSP 1kHz test tone mode ON)

Adjust radio board R26 for minimum modulation distortion at demodulated
carrier

≤

1.0 % THD+N

(0.7)

Adjust radio board R47 for 100kHz peak deviation at radio board J3

99 to 101 kHz

(100)

Press MENU/SEL button on the test panel key pad (Lowest carrier freq is highlighted)

channel=XX

set channel (0(00) to 1020 (ff) in normal
tuning mode, 80 is 512)

Measure distortion at demodulated carrier, fine adjusting radio board R26 if
required

≤

1.2 % THD+N

(0.7)

Press UP or DWN button on the test panel key pad for 100 kHz peak carrier
deviation at radio board J3

99 to 101 kHz

(100)

devoff(0)? (Get deviation offset setting for the Low
channel) (+10 to -10). devoff(0)=x (set deviation

offset for 100KHz)(1KHz steps).

99 to 101 kHz (100)

Press MENU/SEL button on the test panel key pad (Highest carrier freq is highlighted)

channel=XX

set channel (0(00) to 1020 (ff) in normal

tuning mode, 80 is 512)

Measure distortion at demodulated carrier, fine adjusting radio board R26 if
required

≤

1.2 % THD+N

(0.7)

Press UP or DWN button on the test panel key pad for 100 kHz peak carrier
deviation at radio board J3

99 to 101 kHz

(100)

devoff(1)? (Get deviation offset setting for the high

channel) (+10 to -10). devoff(1)=x (set deviation
offset for 100KHz)(1KHz steps).

99 to 101 kHz (100)

Repeat this step until no further adjustment is necessary

Summary of Contents for HH




























Search results

Summary of Contents for HH

Reviews:

Related manuals for HH

Brands by name

Popular brands

Lectrosonics HH, Alignment Procedure

Search results

Summary of Contents for HH

Reviews:

Related manuals for HH

Brands by name

Popular brands