manualshive.com logo in svg

Lectronics Venue 2-941, Installation Manual, Page: 10 / 32

Share
Download
Lectronics Venue 2-941 Installation Manual Download Page 10

Venue 2 Wideband Receiver

LECTROSONICS, INC.

10

LCD Interface

When the receiver is turned on, LCD will show the 

model number, firmware version and serial number 

during the boot sequence. When the sequence is com-

pleted, the Main Window will display the status and 

activity of the installed receivers.

Setup and monitoring can be done directly on the front 

panel keypad interface. It is worthwhile to become fa-

miliar with the front panel controls even if you only use 

it for monitoring and to check settings.

Receiver select buttons

Receiver 

installed, 

no Tx active

Receiver 

installed, 

Tx active

No receivers installed

BACK button

Rotary encoder

The menu structure is comprehensive but easy to 

navigate. Three menus provide easy access to setup 

screens and monitoring.

Top Menu

These are the system level settings that are common 

to all channels.

Rx Menu

Each receiver module has unique settings 

Tx Menu

The settings for transmitters with IR ports can be 

configured in the receiver and then transferred to the 

transmitters via the IR ports. 

Navigating the Menus

Three menus are provided for complete system setup:

•  Top Menu for overall system settings
•  RX Menu for setup of the receiver modules
•  TX Menu for setup of the transmitters

Press the rotary encoder to enter the menu system. 

The first screen that appears is the Top Menu with 

links to the RX (receiver) and TX (transmitter) menus.

Selected menu is shown at top left

Link to RX Menu

Link to TX Menu

Turn the rotary encoder to navigate through the avail-

able items. The selected item appears highlighted in 

the center of the LCD. Press the rotary encoder to en-

ter the setup screen for the selected item, or navigate 

to another menu.

The first item that appears in the RX and TX menus is 

a link back to the top menu.

Refer to the Menu Map on the following pages for a 

listing and descriptions of all menu items.

Summary of Contents for Venue 2-941

































Reviews:

No comments