General instructions
• Always switch the appliance on first by pressing the On/Off button.
• When the selected function is lit, the oven begins to heat up or the time set begins to count
down.
• When the selected temperature is reached, an audible signal sounds.
• The oven light is switched on as long as an oven function is started.
• The oven light is goes off after 10 minutes when the appliance switched off automatically.
• Switch appliance off using the On/Off button.
Selecting the oven function
1.
Switch on the oven with the On/Off
button.
2.
Press the or button repeatedly untial the desired oven function appears.
• A suggested temperature appears on the temperature diplay.
• If the suggested temperature is not changed within approx. 5 seconds, the oven begins to
heat up.
Changing the oven temperature
Press the or button, to raise or lower the temperature. The setting changes in steps
of 5°C.
Thermometer symbol
• The slowly rising thermometer symbol indicates how hot the oven is as it heats up.
The three segments of the thermometer symbol show that Fast Warm Up is working.
Changing the oven function
To change the oven function, Press the or button repeatedly untial the desired oven
function is displayed.
Switching off the oven
Switch off the appliance using the On/Off button.
Speedcook
After an oven function is selected, with the use of the additional function Speedcook the
empty oven can be pre-heated in a relatively shore time.
Important:
Do not put the food to be cooked into the oven,
until Speedcook is completed
and the oven is operating using the desired function.
1.
Set the desired function. If necessary, change the suggested temperature.
2.
Press the Speedcook button. The symbol lights up:
The bars flashing one after another show that Speedcook is operating.
When the temperature set is reached, the bars of the heat indicator light up. An audible
signal sounds. The symbol goes out.
The oven now continues heating according to the pre-set oven function and temperature.
You can now place the food in the oven.
Memory function
The Memory function can be used to save a setting which is frequently used.
1.
Set oven function, temperature and If necessary the clock functions Clock time
and/or End time .
2.
Press and hold the button for approx. 2 seconds, untial an acoustic signal sounds.
The setting is saved.
To save another setting, press the button for approx. 2 seconds. The previously saved
setting is replaced by the new one.
Starting the Memory function
1.
Switch the oven on using the button On/Off
.
2.
Using the button call up the saved setting.
Clock Functions
Countdown
To set a countdown. A signal sounds after the time has elapsed.
This function does not affect the operation of the oven.
- Only use the appliance to cook food and nothing else;
- Check the soundness of the appliance after it has been unpacked;
- Disconnect the appliance from the electrical mains if it is not functioning properly and before
cleaning or performing maintenance;
- When left unused, unplug the appliance form the electricity mains;
- Use oven gloves to place cookware in the oven or when removing it;
- Always grip the oven door handle in the center as the extremities of the same may be hot
due to any hot air leaks;
- Cut the power supply cable after disconnecting it from the mains when you decide not to
use the appliance any longer.
• The manufacturer may not be held responsible for any damage due to :Incorrect installation,
improper, incorrect and irrational use.
Installation
Only a qualified person in compliance with the instructions provided must install the
appliance.
The manufacturer declines all responsibility for improper installation, which may
harm persons and animals and damage property.
Important:
- The power supply to the appliance must be cut off before any adjustments or
maintenance work is done onit;
- Air duct is supposed to use in Ventilation.
Installation of Built-in Ovens
In order to ensure that the built-in appliance functions properly, the cabinet containing it must
be appropriate. The figure below gives the dimensions of the cut-out for installation under the
counter or in a wall cabinet unit.
N. B :Installation in compliance with the consumption declaration
In order to ensure adequate ventilation ,the back panel of the cabinet unit must be removed.
Installing the oven so that it rests on two strips of wood is preferable. If the oven rests on a
continuous, flat surface, there must be an aperture of at least 45×560mm.
The panels of the adjacent cabinets must be made of heat-resistant material. In particular ,
cabinets with a veneer
45 mm
．
560
mm
．
4
13
